ATmega169P Atmel Corporation, ATmega169P Datasheet - Page 229

• Manufacturer Part Number: ATmega169P
• Manufacturer: Atmel Corporation

Specifications of ATmega169P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

22.9
22.9.1
8018P–AVR–08/10
ADC Register Description
ADMUX – ADC Multiplexer Selection Register
• Bit 7:6 – REFS1:0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in
changed during a conversion, the change will not go in effect until this conversion is complete
(ADIF in ADCSRA is set). The internal voltage reference options may not be used if an external
reference voltage is being applied to the AREF pin.
Table 22-3.
• Bit 5 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC Data Register.
Write one to ADLAR to left adjust the result. Otherwise, the result is right adjusted. Changing the
ADLAR bit will affect the ADC Data Register immediately, regardless of any ongoing conver-
sions. For a complete description of this bit, see
page
• Bits 4:0 – MUX4:0: Analog Channel Selection Bits
The value of these bits selects which combination of analog inputs are connected to the ADC.
See
change will not go in effect until this conversion is complete (ADIF in ADCSRA is set).
Bit
(0x7C)
Read/Write
Initial Value
REFS1
0
0
1
1
Table 22-4 on page 230
232.
REFS0
Voltage Reference Selections for ADC
0
1
0
1
REFS1
R/W
7
0
Voltage Reference Selection
AREF, Internal Vref turned off
AVCC with external capacitor at AREF pin
Reserved
Internal 1.1V Voltage Reference with external capacitor at AREF pin
REFS0
R/W
6
0
for details. If these bits are changed during a conversion, the
ADLAR
R/W
5
0
MUX4
R/W
4
0
”ADCL and ADCH – ADC Data Register” on
MUX3
R/W
3
0
MUX2
R/W
2
0
Table
MUX1
ATmega169P
R/W
1
0
22-3. If these bits are
MUX0
R/W
0
0
ADMUX
229