ATmega169P Atmel Corporation, ATmega169P Datasheet - Page 58

• Manufacturer Part Number: ATmega169P
• Manufacturer: Atmel Corporation

Specifications of ATmega169P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8018P–AVR–08/10
When the BOOTRST Fuse is unprogrammed, the Boot section size set to 2 Kbytes and the
IVSEL bit in the MCUCR Register is set before any interrupts are enabled, the most typical and
general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed and the Boot section size set to 2 Kbytes, the most
typical and general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed, the Boot section size set to 2 Kbytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses is:
0x0031
0x0032
0x0033
Address Labels Code
0x0000
0x0001
0x0002
0x0003
0x0004
0x0005
;
.org 0x1C02
0x1C02
0x1C04
...
0x1C2C
Address Labels Code
.org 0x0002
0x0002
0x0004
...
0x002C
;
.org 0x1C00
0x1C00
0x1C01
0x1C02
0x1C03
0x1C04
0x1C05
Address Labels Code
;
.org 0x1C00
0x1C00
0x1C02
0x1C04
...
0x1C2C
...
RESET: ldi
RESET: ldi
...
out
sei
<instr>
out
ldi
out
sei
<instr>
jmp
jmp
...
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
jmp
jmp
jmp
...
jmp
...
...
SPL,r16
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
EXT_INT0
PCINT0
...
SPM_RDY
EXT_INT0
PCINT0
...
SPM_RDY
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
RESET
EXT_INT0
PCINT0
...
SPM_RDY
xxx
xxx
xxx
Comments
; Enable interrupts
Comments
; Set Stack Pointer to top of RAM
; Enable interrupts
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
Comments
; Reset handler
; IRQ0 Handler
; PCINT0 Handler
;
; Store Program Memory Ready Handler
ATmega169P
58