ATmega169P Atmel Corporation, ATmega169P Datasheet - Page 240

• Manufacturer Part Number: ATmega169P
• Manufacturer: Atmel Corporation

Specifications of ATmega169P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

23.3.5
23.3.6
23.3.7
8018P–AVR–08/10
Low Power Waveform
Operation in Sleep Mode
Display Blanking
To reduce toggle activity and hence power consumption a low power waveform can be selected
by writing LCDAB to one. Low power waveform requires two subsequent frames with the same
display data to obtain zero DC voltage. Consequently data latching and Interrupt Flag is only set
every second frame. Default and low power waveform is shown in
1/3 bias. For other selections of duty and bias, the effect is similar.
Figure 23-7. Default and Low Power Waveform
When synchronous LCD clock is selected (LCDCS = 0) the LCD display will operate in Idle
mode and Power-save mode with any clock source.
An asynchronous clock from TOSC1 can be selected as LCD clock by writing the LCDCS bit to
one when Calibrated Internal RC Oscillator is selected as system clock source. The LCD will
then operate in Idle mode, ADC Noise Reduction mode and Power-save mode.
When EXCLK in ASSR Register is written to one, and asynchronous clock is selected, the exter-
nal clock input buffer is enabled and an external clock can be input on Timer Oscillator 1
(TOSC1) pin instead of a 32 kHz crystal. See
page 150
Before entering Power-down mode, Standby mode or ADC Noise Reduction mode with synchro-
nous LCD clock selected, the user have to disable the LCD. Refer to
page
When LCDBL is written to one, the LCD is blanked after completing the current frame. All seg-
ments and common pins are connected to GND, discharging the LCD. Display memory is
preserved. Display blanking should be used before disabling the LCD to avoid DC voltage
across segments, and a slowly fading image.
-
-
244.
2
1
2
1
2
1
1
2
/
/
/
/
/
/
/
/
3
3
3
3
3
3
3
3
-V
V
V
V
GND
V
V
V
GND
V
V
V
GND
V
V
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
for further details.
Frame
Frame
SEG0
COM0
SEG0 - COM0
”Asynchronous operation of the Timer/Counter” on
-
-
2
1
2
1
2
1
1
2
/
/
/
/
/
/
/
/
3
3
3
3
3
3
3
3
-V
V
V
V
GND
V
V
V
GND
V
V
V
GND
V
V
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
Frame
Figure 23-7
ATmega169P
Frame
”Disabling the LCD” on
SEG0
COM0
SEG0 - COM0
for 1/3 duty and
240