ATmega169P Atmel Corporation, ATmega169P Datasheet - Page 272

• Manufacturer Part Number: ATmega169P
• Manufacturer: Atmel Corporation

Specifications of ATmega169P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.6
8018P–AVR–08/10
Boundary-scan Order
Table 25-4.
Using this algorithm, the timing constraint on the HOLD signal constrains the TCK clock fre-
quency. As the algorithm keeps HOLD high for five steps, the TCK clock frequency has to be at
least five times the number of scan bits divided by the maximum hold time, t
Table 25-5
selected as data path. Bit 0 is the LSB; the first bit scanned in, and the first bit scanned out. The
scan order follows the pin-out order as far as possible. Therefore, the bits of Port A is scanned in
the opposite bit order of the other ports. Exceptions from the rules are the Scan chains for the
analog circuits, which constitute the most significant bits of the scan chain regardless of which
physical pin they are connected to. In
PXn. Control corresponds to FF1, and PXn. Pull-up_enable corresponds to FF2. Bit 4, bit 5, bit
6, and bit 7 of Port F is not in the scan chain, since these pins constitute the TAP pins when the
JTAG is enabled.
Table 25-5.
Step
1
2
3
4
5
6
7
8
9
10
11
Bit Number
197
196
195
194
Actions
SAMPLE_P
RELOAD
EXTEST
Verify the
COMP bit
scanned out
to be 0
Verify the
COMP bit
scanned out
to be 1
shows the Scan order between TDI and TDO when the Boundary-scan chain is
Algorithm for Using the ADC
ATmega169P Boundary-scan Order
Signal Name
AC_IDLE
ACO
ACME
AINBG
ADCEN
1
1
1
1
1
1
1
1
1
1
1
DAC
0x200
0x200
0x200
0x123
0x123
0x200
0x200
0x200
0x143
0x143
0x200
Figure 25-3 on page
MUXEN
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
0x08
HOLD
1
0
1
1
1
1
0
1
1
1
1
Module
Comparator
263, PXn. Data corresponds to FF0,
PRECH
1
1
1
1
0
1
1
1
1
0
1
PA3.
Data
ATmega169P
0
0
0
0
0
0
0
0
0
0
0
hold,max
PA3.
Control
0
0
0
0
0
0
0
0
0
0
0
PA3.
Pull-up_
Enable
0
0
0
0
0
0
0
0
0
0
0
272