LPC2478FBD208,551 NXP Semiconductors, LPC2478FBD208,551 Datasheet - Page 407

• Manufacturer Part Number: LPC2478FBD208,551
• Description: IC ARM7 MCU 512K LCD 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2478FBD208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/IrDA/SPI/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, DK-35TS-LPC2478, DK-57TS-LPC2478, DK-57VTS-LPC2478, SOMDIMM-LPC2478, SAB-TFBGA208, KSK-LPC2478-JL, MCB2470
• Development Tools By Supplier: OM11015, OM11019, OM11022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1034 - PROGRAMMERS, DEVELOPMENT SYSTEMS622-1033 - KIT LCD TOUCH 5.7" FOR LPC2478MCB2470 - BOARD EVAL NXP LPC247X SERIESOM11022 - EVAL LPC-STICK WITH LPC2478OM11019 - BOARD EVAL FOR LPC2478568-4742 - MODULE DIMM LPC2478 ARM7568-4741 - KIT LCD TOUCH 5.7" FOR LPC2478622-1028 - KIT LCD TOUCH 5.7" FOR LPC2478KSDKLPC2478-PL - KIT IAR KICKSTART NXP LPC2478622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4369 - BOARD EVAL FOR LPC2478622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4363; 935284069551; LPC2478FBD208-S

NXP Semiconductors
UM10237_4
User manual
Table 372. I2C status register (I2C_STS - address 0xFFE0 C304) bit description
Bit
0
1
2
3
4
5
6
7
Symbol Value Description
TDI
AFI
NAI
DRMI
DRSI
Active
SCL
SDA
0
1
0
1
0
1
0
1
0
1
Rev. 04 — 26 August 2009
Transaction Done Interrupt. This flag is set if a transaction
completes successfully. It is cleared by writing a one to bit 0 of
the status register. It is unaffected by slave transactions.
Transaction has not completed.
Transaction completed.
Arbitration Failure Interrupt. When transmitting, if the SDA is low
when SDAOUT is high, then this I
another device on the bus. The Arbitration Failure bit is set when
this happens. It is cleared by writing a one to bit 1 of the status
register.
No arbitration failure on last transmission.
Arbitration failure occurred on last transmission.
No Acknowledge Interrupt. After every byte of data is sent, the
transmitter expects an acknowledge from the receiver. This bit is
set if the acknowledge is not received. It is cleared when a byte
is written to the master TX FIFO.
Last transmission received an acknowledge.
Last transmission did not receive an acknowledge.
Master Data Request Interrupt. Once a transmission is started,
the transmitter must have data to transmit as long as it isn’t
followed by a stop condition or it will hold SCL low until more
data is available. The Master Data Request bit is set when the
master transmitter is data-starved. If the master TX FIFO is
empty and the last byte did not have a STOP condition flag, then
SCL is held low until the CPU writes another byte to transmit.
This bit is cleared when a byte is written to the master TX FIFO.
Master transmitter does not need data.
Master transmitter needs data.
Slave Data Request Interrupt. Once a transmission is started,
the transmitter must have data to transmit as long as it isn’t
followed by a STOP condition or it will hold SCL low until more
data is available. The Slave Data Request bit is set when the
slave transmitter is data-starved. If the slave TX FIFO is empty
and the last byte transmitted was acknowledged, then SCL is
held low until the CPU writes another byte to transmit. This bit is
cleared when a byte is written to the slave Tx FIFO.
Slave transmitter does not need data.
Slave transmitter needs data.
Indicates whether the bus is busy. This bit is set when a START
condition has been seen. It is cleared when a STOP condition is
seen..
The current value of the SCL signal.
The current value of the SDA signal.
Chapter 15: LPC24XX USB OTG controller
2
C has lost the arbitration to
UM10237
© NXP B.V. 2009. All rights reserved.
407 of 792
Reset
Value
0
0
0
0
0
0
-
-