M30260F6AGP#U5A Renesas Electronics America, M30260F6AGP#U5A Datasheet - Page 134

• Manufacturer Part Number: M30260F6AGP#U5A
• Description: IC M16C MCU FLASH 48K 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30260F6AGP#U5A

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 39
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: R8C
• Device Core Size: 16b
• Frequency (max): 20MHz
• Interface Type: UART
• Total Internal Ram Size: 2KB
• # I/os (max): 39
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 12-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: R8C
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 39
• Number Of Timers: 8
• For Use With: R0K33026AS000BE - KIT DEV EVALUATION M16C/26A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

R
R
M
e
E
. v
J
1
Table 12.2.4.1 A/D Trigger Mode Specifications
0
6
12.2.4 A/D Trigger Mode
Count Source
Count Operation
Divide Ratio
Count Start Condition
Count Stop Condition
Interrupt Request
Generation Timing
TBiIN Pin Function
Read From Timer
Write To Timer
NOTES:
2
9
C
0 .
B
A/D trigger mode is used as conversion start trigger for A/D converter in simultaneous sample sweep
mode of A/D conversion or delayed trigger mode 0. This mode is used as conversion start trigger of A/D
converter. A/D trigger mode is used in Timer B0 and Timer B1. In this mode, the timer starts counting by
one trigger until the count value becomes 0000
trigger mode and figure 12.2.4.2 shows the TB2SC register.
2 /
0
0
1. A/D conversion is started by the timer underflow. For details refer to Section 14. A/D Converter.
2. When using in delayed trigger mode 0, set the larger value than the value of the timer B0 register
2
6
0
F
A
2
to the timer B1 register.
e
0 -
b
G
1 .
2
Item
o r
0
, 5
0
u
2
p
0
(
0
(2)
M
7
1
6
page 115
C
2 /
6
, A
f
• Down count
• When the timer underflows, reload register contents are reloaded before
• When a trigger is generated during the count operation, the count is not
When the TBiS (i=0,1) bit in the TABSR register is "1"(count started), TBiEN
(i=0,1) bit in TB2SC register is "1", and the following trigger is generated.
(Selection based on TB2SEL bit in the TB2SC register)
• Timer B2 overflow or underflow
• Underflow of Timer B2 interrupt generation frequency counter setting
• After the count value is 0000
• Set the TBiS bit to "0"(count stopped)
Timer underflows
I/O port
• When writing in the TBi register during count stopped.
• When writing in the TBi register during count.
M
Count value can be read by reading TBi register
1
stopping counting
affected
1/(n+1)
Value is written to both reload register and counter
Value is written to only reload register (Transfered to counter when reloaded next)
f o
, f
1
6
2
3
C
, f
2
9
2 /
8
, f
6
, B
32
, and f
n: Setting value of TBi register (i=0,1)
M
1
0000
6
C
C32
(1)
2 /
16
6
-FFFF
) T
16
. Figure 12.2.4.1 shows the TBiMR register in A/D
16
Specification
16
and reload register contents are reloaded
12. Timer