M30260F6AGP#U5A Renesas Electronics America, M30260F6AGP#U5A Datasheet - Page 64

• Manufacturer Part Number: M30260F6AGP#U5A
• Description: IC M16C MCU FLASH 48K 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30260F6AGP#U5A

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 39
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: R8C
• Device Core Size: 16b
• Frequency (max): 20MHz
• Interface Type: UART
• Total Internal Ram Size: 2KB
• # I/os (max): 39
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 12-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: R8C
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 39
• Number Of Timers: 8
• For Use With: R0K33026AS000BE - KIT DEV EVALUATION M16C/26A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

R
R
M
e
E
7.1 Main Clock
. v
J
1
Figure 7.1.1. Examples of Main Clock Connection Circuit
0
6
The following describes the clocks generated by the clock generation circuit.
The main clock is generated by the main clock oscillation circuit. This clock is used as the clock source for
the CPU and peripheral function clocks. The main clock oscillator circuit is configured by connecting a
resonator between the X
which is disconnected from the oscillator circuit during stop mode in order to reduce the amount of power
consumed in the chip. The main clock oscillator circuit may also be configured by feeding an externally
generated clock to the X
The main clock after reset oscillates in the M16C/26A and M16C/26B, but stop in the M16C/26T.
The power consumption in the chip can be reduced by setting the CM05 bit in the CM0 register to “1” (main
clock oscillator circuit turned off) after switching the clock source for the CPU clock to a sub clock or on-chip
oscillator clock. In this case, X
on, X
During stop mode, all clocks including the main clock are turned off. Refer to 7.6 power control.
If the main clock is not used, it is recommended to connect the XIN pin to VCC to reduce power consump-
tion during reset.
2
9
C
0 .
B
2 /
0
0
2
6
0
F
IN
A
2
e
0 -
b
G
is pulled “H” to X
1 .
2
o r
0
(Built-in Feedback Resistor)
, 5
0
u
2
p
0
(
0
M
7
NOTE:
1
6
MCU
1. Insert a damping resistor if required. Resistance value varies depending on the oscillator setting.
2. The external clock should not be stopped when it is connected to the X
C
page 45
Use resistance value recommended by the oscillator manufacturer. If the oscillator manufacturer
recommends that a feedback resistor be added to the chip externally, insert a feedback resistor
between X
selected as the CPU clock.
2 /
X
OUT
V
6
X
SS
IN
OUT
, A
IN
IN
pin. Figure 7.1.1 shows the examples of main clock connection circuit.
M
and X
IN
via the feedback resistor.
f o
1
Oscillator
OUT
6
and X
Rd
3
C
2
(1)
2 /
OUT
9
goes “H”. Furthermore, because the internal feedback resistor remains
OUT
6
, B
.
pins. The main clock oscillator circuit contains a feedback resistor,
M
1
6
C
C
OUT
C
IN
2 /
6
) T
(Built-in Feedback Resistor)
MCU
X
OUT
X
IN
Open
V
V
CC
SS
IN
External Clock
pin and the main clock is
7. Clock Generation Circuit