AT90PWM81-16SN Atmel, AT90PWM81-16SN Datasheet - Page 181

• Manufacturer Part Number: AT90PWM81-16SN
• Description: IC MCU AVR 8K FLASH ISP 20SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM81-16SN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: Brown-out Detect/Reset, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 20-SOIC (7.5mm Width)
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 16 MHz
• Number Of Timers: 1
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Height: 2.35 mm
• Length: 13 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7.6 mm
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7734P–AVR–08/10
The interconnection between Master and Slave CPUs with SPI is shown in
sists of two shift Registers, and a Master clock generator. The SPI Master initiates the communication
cycle when pulling low the Slave Select SS pin of the desired Slave. Master and Slave prepare the data to
be sent in their respective shift Registers, and the Master generates the required clock pulses on the SCK
line to interchange data. Data is always shifted from Master to Slave on the Master Out – Slave In, MOSI,
line, and from Slave to Master on the Master In – Slave Out, MISO, line. After each data packet, the Mas-
ter will synchronize the Slave by pulling high the Slave Select, SS, line.
When configured as a Master, the SPI interface has no automatic control of the SS line. This must be han-
dled by user software before communication can start. When this is done, writing a byte to the SPI Data
Register starts the SPI clock generator, and the hardware shifts the eight bits into the Slave. After shifting
one byte, the SPI clock generator stops, setting the end of transmission flag (SPIF). If the SPI Interrupt
Enable bit (SPIE) in the SPCR Register is set, an interrupt is requested. The Master may continue to shift
the next byte by writing it into SPDR, or signal the end of packet by pulling high the Slave Select, SS line.
The last incoming byte will be kept in the Buffer Register for later use.
When configured as a Slave, the SPI interface will remain sleeping with MISO tri-stated as long as the SS
pin is driven high. In this state, software may update the contents of the SPI Data Register, SPDR, but the
data will not be shifted out by incoming clock pulses on the SCK pin until the SS pin is driven low. As one
byte has been completely shifted, the end of transmission flag, SPIF is set. If the SPI Interrupt Enable bit,
SPIE, in the SPCR Register is set, an interrupt is requested. The Slave may continue to place new data to
be sent into SPDR before reading the incoming data. The last incoming byte will be kept in the Buffer
Register for later use.
Figure 14-2.
The system is single buffered in the transmit direction and double buffered in the receive direction. This
means that bytes to be transmitted cannot be written to the SPI Data Register before the entire shift cycle
is completed. When receiving data, however, a received character must be read from the SPI Data Regis-
ter before the next character has been completely shifted in. Otherwise, the first byte is lost.
In SPI Slave mode, the control logic will sample the incoming signal of the SCK pin. To ensure correct
sampling of the clock signal, the frequency of the SPI clock should never exceed f
SPI Master-slave Interconnection
Figure
AT90PWM81
clkio
14-2. The system con-
/4.
SHIFT
ENABLE
181