AT90PWM81-16SN Atmel, AT90PWM81-16SN Datasheet - Page 98

• Manufacturer Part Number: AT90PWM81-16SN
• Description: IC MCU AVR 8K FLASH ISP 20SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM81-16SN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: Brown-out Detect/Reset, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 20-SOIC (7.5mm Width)
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 16 MHz
• Number Of Timers: 1
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Height: 2.35 mm
• Length: 13 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7.6 mm
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.8.5
98
AT90PWM81
Timer/Counter1 Interrupt Flag Register – TIFR1
• Bit 7, 6 – Res: Reserved Bits
These bits are unused bits in the AT90PWM81, and will always read as zero.
• Bit 5 – ICIE1: Timer/Counter1, Input Capture Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally enabled), the
Timer/Counter1 Input Capture interrupt is enabled. The corresponding Interrupt Vector (see XXXX) is
executed when the ICF1 Flag, located in TIFR1, is set.
• Bit 4, 3, 2,1 – Res: Reserved Bits
These bits are unused bits in the AT90PWM81, and will always read as zero.
• Bit 0 – TOIE1: Timer/Counter1, Overflow Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally enabled), the
Timer/Counter1 Overflow interrupt is enabled. The corresponding Interrupt Vector (see
61) is executed when the TOV1 Flag, located in TIFR1, is set.
• Bit 7, 6 – Res: Reserved Bits
These bits are unused bits in the AT90PWM81, and will always read as zero.
• Bit 5 – ICF1: Timer/Counter1, Input Capture Flag
This flag is set when a capture event occurs on the ICP1 pin. When the Input Capture Register (ICR1) is
set by the WGM13:0 to be used as the TOP value, the ICF1 Flag is set when the counter reaches the TOP
value.
ICF1 is automatically cleared when the Input Capture Interrupt Vector is executed. Alternatively, ICF1
can be cleared by writing a logic one to its bit location.
• Bit 4, 3, 2,1 – Res: Reserved Bits
• Bit 0 – TOV1: Timer/Counter1, Overflow Flag
The setting of this flag is dependent of the WG.
TOV1 is automatically cleared when the Timer/Counter1 Overflow Interrupt Vector is executed. Alterna-
tively, TOV1 can be cleared by writing a logic one to its bit location.
Bit
Read/Write
Initial Value
7
–
R
0
R
6
–
0
5
ICF1
R/W
0
4
–
R
0
3
–
R
0
2
–
R/W
0
1
–
R/W
0
0
TOV1
R/W
0
Table 8-1 on page
7734P–AVR–08/10
TIFR1