PIC18F65J90-I/PT Microchip Technology, PIC18F65J90-I/PT Datasheet - Page 248

• Manufacturer Part Number: PIC18F65J90-I/PT
• Description: IC PIC MCU FLASH 16KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F65J90-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 51
• Ram Memory Size: 2KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 2
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: AUSART, EUSART, I2C, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183030
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F85J90 FAMILY
17.4.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA1<5>), or the Continuous Receive
Enable bit, CREN (RCSTA1<4>). Data is sampled on
the RX1 pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 17-13:
TABLE 17-8:
DS39770B-page 246
INTCON
PIR1
PIE1
IPR1
RCSTA1
RCREG1
TXSTA1
BAUDCON1 ABDOVF
SPBRGH1
SPBRG1
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
RC6/TX1/CK1 pin
RC6/TX1/CK1 pin
Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
Name
Initialize the SPBRGH1:SPBRG1 registers for the
appropriate baud rate. Set or clear the BRG16 bit,
as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
RC7/RX1/DT1
(SCKP = 0)
(SCKP = 1)
(Interrupt)
RC1IF bit
CREN bit
RCREG1
SREN bit
SREN bit
Write to
EUSART SYNCHRONOUS
MASTER RECEPTION
Read
pin
EUSART Receive Register
EUSART Baud Rate Generator Register High Byte
EUSART Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
Q2
CSRC
SPEN
Bit 7
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘0’
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
—
—
—
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
RCMT
ADIF
ADIE
ADIP
Bit 6
RX9
TX9
bit 0
RC1IF
RC1IE
RC1IP
SREN
TXEN
Bit 5
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 1
—
Preliminary
bit 2
INT0IE
TX1IE
TX1IP
CREN
SYNC
TX1IF
SCKP
Bit 4
bit 3
ADDEN
SENDB
BRG16
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
SSPIE
SSPIP
SSPIF
RBIE
Bit 3
Ensure bits, CREN and SREN, are clear.
If interrupts are desired, set enable bit, RC1IE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
Interrupt flag bit, RC1IF, will be set when recep-
tion is complete and an interrupt will be generated
if the enable bit, RC1IE, was set.
Read the RCSTA1 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG1 register.
bit, CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
bit 4
TMR0IF
BRGH
FERR
Bit 2
—
—
—
—
bit 5
TMR2IE
TMR2IP
TMR2IF
INT0IF
OERR
TRMT
© 2007 Microchip Technology Inc.
WUE
bit 6
Bit 1
TMR1IF
TMR1IE
TMR1IP
ABDEN
bit 7
RX9D
TX9D
RBIF
Bit 0
Q1 Q2 Q3 Q4
on Page
Values
Reset
51
54
54
54
53
53
53
55
55
53
‘0’