PIC18F27J13-I/SS Microchip Technology, PIC18F27J13-I/SS Datasheet - Page 409

• Manufacturer Part Number: PIC18F27J13-I/SS
• Description: IC PIC MCU 128KB FLASH 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J13-I/SS

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Digital Ic Case Style: SSOP
• Supply Voltage Range: 1.8V To 5.5V
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 19
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DM164128, DM180021, DM183026-2, DV164131, MA180030, DM183022, DM183032, DV164136, MA180024
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180030 - BOARD DEMO PIC18F47J13 FS USBMA180029 - BOARD DEMO PIC18F47J53 FS USB
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

26.7
26.7.1
When the device enters any Sleep mode, the CTMU
module current source is always disabled. If the CTMU
is performing an operation that depends on the current
source when Sleep mode is invoked, the operation may
not
measurements may return erroneous values.
26.7.2
The behavior of the CTMU in Idle mode is determined
by the CTMUSIDL bit (CTMUCONH<5>). If CTMUSIDL
is cleared, the module will continue to operate in Idle
mode. If CTMUSIDL is set, the module’s current source
is disabled when the device enters Idle mode. In this
case, if the module is performing an operation when
Idle mode is invoked, the results will be similar to those
with Sleep mode.
 2010 Microchip Technology Inc.
terminate
Operation During Sleep/Idle
Modes
SLEEP MODE AND DEEP SLEEP
MODES
IDLE MODE
correctly.
Capacitance
and
time
Preliminary
PIC18F47J13 FAMILY
26.8
Upon Reset, all registers of the CTMU are cleared. This
leaves the CTMU module disabled; its current source is
turned off and all configuration options return to their
default settings. The module needs to be re-initialized
following any Reset.
If the CTMU is in the process of taking a measurement
at the time of Reset, the measurement will be lost. A
partial charge may exist on the circuit that was being
measured, and should be properly discharged before
the CTMU makes subsequent attempts to make a
measurement. The circuit is discharged by setting and
then clearing the IDISSEN bit (CTMUCONH<1>) while
the A/D Converter is connected to the appropriate
channel.
Effects of a Reset on CTMU
DS39974A-page 409