MCHC908GR8CFAE Freescale Semiconductor, MCHC908GR8CFAE Datasheet - Page 62

• Manufacturer Part Number: MCHC908GR8CFAE
• Description: IC MCU FLSH 8BIT8MHZ 7.5K32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Computer Operating Properly (COP) Module
The COP counter is a free-running 6-bit counter preceded by a 12-bit prescaler counter. If not cleared by
software, the COP counter overflows and generates an asynchronous reset after 262,128 or 8176
COPCLK cycles, depending on the state of the COP rate select bit, COPRS, in the configuration register.
With a 8176 COPCLK cycle overflow option, a 32.768-kHz crystal gives a COP timeout period of 250 ms.
Writing any value to location $FFFF before an overflow occurs prevents a COP reset by clearing the COP
counter and stages 12 through 5 of the prescaler.
A COP reset pulls the RST pin low for 32 COPCLK cycles and sets the COP bit in the reset status register
(RSR).
In monitor mode, the COP is disabled if the RST pin or the IRQ1 is held at V
V
5.3 I/O Signals
The following paragraphs describe the signals shown in
5.3.1 COPCLK
COPCLK is a clock generated by the clock selection circuit in the internal clock generator (ICG). See
Clock Selection Circuit
5.3.2 STOP Instruction
The STOP instruction clears the COP prescaler.
5.3.3 COPCTL Write
Writing any value to the COP control register (COPCTL) (see
counter and clears bits 12 through 5 of the prescaler. Reading the COP control register returns the low
byte of the reset vector.
5.3.4 Power-On Reset
The power-on reset (POR) circuit clears the COP prescaler 4096 CGMXCLK cycles after power-up.
5.3.5 Internal Reset
An internal reset clears the COP prescaler and the COP counter.
62
TST
on the RST pin disables the COP.
Service the COP immediately after reset and before entering or after exiting
stop mode to guarantee the maximum time before the first COP counter
overflow.
Place COP clearing instructions in the main program and not in an interrupt
subroutine. Such an interrupt subroutine could keep the COP from
generating a reset even while the main program is not working properly.
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
for more details.
NOTE
NOTE
Figure
5.4 COP Control
5-1.
TST
Register) clears the COP
. During the break state,
Freescale Semiconductor
7.3.5