MCHC908GR8CFAE Freescale Semiconductor, MCHC908GR8CFAE Datasheet - Page 82

• Manufacturer Part Number: MCHC908GR8CFAE
• Description: IC MCU FLSH 8BIT8MHZ 7.5K32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Internal Clock Generator (ICG) Module)
7.3.2.3 Frequency Comparator
The frequency comparator effectively compares the low-frequency base clock (IBASE) to a nominal
frequency, f
capacitor with a current reference for a period dependent on IBASE. This voltage is compared to a voltage
reference with comparators, whose outputs are fed to the digital loop filter. The dependence of these
outputs on the capacitor size, current reference, and voltage reference causes up to ±25 percent error in
f
7.3.2.4 Digital Loop Filter
The digital loop filter (DLF) uses the outputs of the frequency comparator to adjust the internal clock
(ICLK) clock period. The DLF generates the DCO divider control bits (DDIV[3:0]) and the DCO stage
control bits (DSTG[7:0]), which are fed to the DCO. The DLF first concatenates the DDIV and DSTG
registers (DDIV[3:0]:DSTG[7:0]) and then adds or subtracts a value dependent on the relative error in the
low-frequency base clock’s period, as shown in
operating at a V
maximum ($9FF) or below the minimum ($000). In both cases, the value for DDIV will be between $A and
$F. In this range, the DDIV value will be interpreted the same as $9 (the slowest condition). Recovering
from this condition requires subtracting (increasing frequency) in the normal fashion until the value is
again below $9FF. (If the desired value is $9xx, the value may settle at $Axx through $Fxx. This is an
acceptable operating condition.) If the error is less than ±5 percent, the internal clock generator’s filter
stable indicator (FICGS) is set, indicating relative frequency accuracy to the clock monitor.
82
NOM
1. x = Maximum error is independent of value in DDIV[3:0]. DDIV increments or decrements when an addition to DSTG[7:0]
Frequency Error of IBASE
carries or borrows.
.
Compared to f
IBASE < 0.85 f
0.85 f
IBASE < 0.95 f
0.95 f
IBASE < 1.05 f
1.05 f
IBASE < 1.15 f
1.15 f
IBASE < f
f
NOM
NOM
NOM
NOM
NOM
NOM
< IBASE
< IBASE
< IBASE
< IBASE
< IBASE
. First, the frequency comparator converts IBASE to a voltage by charging a known
DD
NOM
NOM
NOM
NOM
NOM
NOM
level which is out of specification, the DLF may attempt to use a value above the
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
Table 7-1. Correction Sizes from DLF to DCO
DDVI[3:0]:DSTG[7:0]
+32 (+$020)
–32 (–$020)
Correction
–8 (–$008)
–1 (–$001)
+1 (+$001)
+8 (+$008)
Table
Minimum
Maximum
Minimum
Maximum
Minimum
Maximum
Minimum
Maximum
Minimum
Maximum
Minimum
Maximum
DDIV[3:0]:DSTG[7:0]
7-1. In some extreme error conditions, such as
Current to New
$xFF to $xDF
$xFF to $xFE
$xFE to $xFF
$xDF to $xFF
$xFF to $xF7
$xF7 to $xFF
$x20 to $x00
$x08 to $x00
$x01 to $x00
$x00 to $x01
$x00 to $x08
$x00 to $x20
(1)
+0.0625/30.9375
–0.0625/17.0625
–0.0625/31
+0.0625/17
–0.5/17.5
+0.5/30.5
Relative Correction
–0.5/31
+0.5/17
–2/31
+2/29
+2/17
–2/19
Freescale Semiconductor
in DCO
+0.202%
–6.45%
–10.5%
–1.61%
–2.86%
–0.202%
–0.366%
+0.368%
+1.64%
+2.94%
+6.90%
+11.8%