MC9S12XA512CAG Freescale Semiconductor, MC9S12XA512CAG Datasheet - Page 1257

• Manufacturer Part Number: MC9S12XA512CAG
• Description: IC MCU 512K FLASH 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XA512CAG

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 80MHz
• Connectivity: EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 119
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: S12XA
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 32 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 119
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12XDP512E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 24 Channel)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

A.3
A.3.1
The time base for all NVM program or erase operations is derived from the oscillator. A minimum
oscillator frequency f
do not have any means to monitor the frequency and will not prevent program or erase operation at
frequencies above or below the specified minimum. Attempting to program or erase the NVM modules at
a lower frequency a full program or erase transition is not assured.
The Flash and EEPROM program and erase operations are timed using a clock derived from the oscillator
using the FCLKDIV and ECLKDIV registers respectively. The frequency of this clock must be set within
the limits specified as f
The minimum program and erase times shown in
maximum f
A.3.1.1
The programming time for single word programming is dependant on the bus frequency as a well as on the
frequency f
A.3.1.2
This applies only to the Flash where up to 64 words in a row can be programmed consecutively using burst
programming by keeping the command pipeline filled. The time to program a consecutive word can be
calculated as:
The time to program a whole row is:
Burst programming is more than 2 times faster than single word programming.
Freescale Semiconductor
NVM, Flash, and EEPROM
NVMOP
bus
NVM Timing
Single Word Programming
Burst Programming
. The maximum times are calculated for minimum f
Unless otherwise noted the abbreviation NVM (nonvolatile memory) is used
for both Flash and EEPROM.
and can be calculated according to the following formula.
NVMOSC
NVMOP
.
is required for performing program or erase operations. The NVM modules
MC9S12XDP512 Data Sheet, Rev. 2.21
t
t
t
swpgm
bwpgm
brpgm
=
=
=
t
9
swpgm
4
NOTE
Table A-17
------------------------ -
f
NVMOP
------------------------ -
f
NVMOP
1
1
+
63 t
+
+
25
bwpgm
9
are calculated for maximum f
----------- -
f
----------- -
f
bus
bus
1
1
NVMOP
and a f
Appendix A Electrical Characteristics
bus
of 2 MHz.
NVMOP
and
1259