C8051F537-IT Silicon Laboratories Inc, C8051F537-IT Datasheet - Page 127

• Manufacturer Part Number: C8051F537-IT
• Description: IC 8051 MCU 2K FLASH 20TSSOP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F53xr

Specifications of C8051F537-IT

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.25 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 336-1401

SFR Definition 13.2. XBR1: Port I/O Crossbar Register 1
13.3. General Purpose Port I/O
Port pins that remain unassigned by the Crossbar and are not used by analog peripherals can be used for
general purpose I/O. Ports P0–P1 are accessed through corresponding special function registers (SFRs)
that are both byte addressable and bit addressable. When writing to a Port, the value written to the SFR is
latched to maintain the output data value at each pin. When reading, the logic levels of the Port's input pins
are returned regardless of the XBRn settings (i.e., even when the pin is assigned to another signal by the
Crossbar, the Port register can always read its corresponding Port I/O pin). The exception to this is the
execution of the read-modify-write instructions that target a Port Latch register as the destination. The
read-modify-write instructions when operating on a Port SFR are the following: ANL, ORL, XRL, JBC, CPL,
INC, DEC, DJNZ and MOV, CLR or SETB, when the destination is an individual bit in a Port SFR. For
these instructions, the value of the latch register (not the pin) is read, modified, and written back to the
SFR.
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bits1–0: PCA0ME: PCA Module I/O Enable Bits.
WEAKPUD XBARE
R/W
Bit7
WEAKPUD: Port I/O Weak Pullup Disable.
0: Weak Pullups enabled (except for Ports whose I/O are configured as analog input).
1: Weak Pullups disabled.
XBARE: Crossbar Enable.
0: Crossbar disabled.
1: Crossbar enabled.
T1E: T1 Enable
0: T1 unavailable at Port pin.
1: T1 routed to Port pin.
T0E: T0 Enable
0: T0 unavailable at Port pin.
1: T0 routed to Port pin.
ECIE: PCA0 External Counter Input Enable
0: ECI unavailable at Port pin.
1: ECI routed to Port pin.
Reserved. Must Write 0b.
00: All PCA I/O unavailable at Port pins.
01: CEX0 routed to Port pin.
10: CEX0, CEX1 routed to Port pins.
11: CEX0, CEX1, CEX2 routed to Port pins.
R/W
Bit6
T1E
R/W
Bit5
T0E
R/W
C8051F52x/F52xA/F53x/F53xA
Bit4
Rev. 1.3
ECIE
R/W
Bit3
Reserved
R/W
Bit2
R/W
Bit1
PCA0ME
SFR Address:
R/W
Bit0
00000000
Reset Value
0xE2
127