XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 27

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
Table 4‐02. XBee‐PRO Commands ‐ Networking & Security (Sub‐categories designated within {brackets})
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
RF Interfacing
Table 4‐03. XBee/XBee‐PRO Commands ‐ RF Interfacing
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
AT
Command
AS ( v1.x80*)
ED ( v1.x80*)
EE ( v1.xA0*)
KY ( v1.xA0*)
AT
Command
PL
CA (v1.x80*)
Command
Category
Networking
{Association}
Networking
{Association}
Networking
{Security}
Networking
{Security}
Command
Category
RF Interfacing
RF Interfacing
Name and Description
Active Scan. Send Beacon Request to Broadcast Address (0xFFFF) and Broadcast
PAN (0xFFFF) on every channel. The parameter determines the time the radio will
listen for Beacons on each channel. A PanDescriptor is created and returned for every
Beacon received from the scan. Each PanDescriptor contains the following information:
CoordAddress (SH, SL)<CR>
CoordPanID (ID)<CR>
CoordAddrMode <CR>
Channel (CH parameter) <CR>
SecurityUse<CR>
ACLEntry<CR>
SecurityFailure<CR>
SuperFrameSpec<CR> (2 bytes):
GtsPermit<CR>
RSSI<CR> (RSSI is returned as -dBm)
TimeStamp<CR> (3 bytes)
<CR>
A carriage return <CR> is sent at the end of the AS command. The Active Scan is
capable of returning up to 5 PanDescriptors in a scan. The actual scan time on each
channel is measured as Time = [(2 ^SD PARAM) * 15.36] ms. Note the total scan time
is this time multiplied by the number of channels to be scanned (16 for the XBee and 13
for the XBee-PRO). Also refer to SD command description.
Energy Scan. Send an Energy Detect Scan. This parameter determines the length of
scan on each channel. The maximal energy on each channel is returned & each value
is followed by a carriage return. An additional carriage return is sent at the end of the
command. The values returned represent the detected energy level in units of -dBm.
The actual scan time on each channel is measured as Time = [(2 ^ED) * 15.36] ms.
Note the total scan time is this time multiplied by the number of channels to be scanned
(refer to SD parameter).
AES Encryption Enable. Disable/Enable 128-bit AES encryption support. Use in
conjunction with the KY command.
AES Encryption Key. Set the 128-bit AES (Advanced Encryption Standard) key for
encrypting/decrypting data. The KY register cannot be read.
Name and Description
Power Level. Select/Read the power level at which the RF modem transmits conducted
power.
NOTE: XBee-PRO RF Modems optimized for use in Japan contain firmware that limits
transmit power output to 10 dBm. If PL=4 (default), the maximum power output level is
fixed at 10 dBm.
CCA Threshold. Set/read the CCA (Clear Channel Assessment) threshold. Prior to
transmitting a packet, a CCA is performed to detect energy on the channel. If the
detected energy is above the CCA Threshold, the modem will not transmit the packet.
0x02 = 16-bit Short Address
0x03 = 64-bit Long Address
bit 15 - Association Permitted (MSB)
bit 14 - PAN Coordinator
bit 13 - Reserved
bit 12 - Battery Life Extension
bits 8-11 - Final CAP Slot
bits 4-7 - Superframe Order
bits 0-3 - Beacon Order
Parameter Range
0 - 6
0 - 6
0 - 1
0 - (any 16-Byte value)
Parameter Range
0 - 4 (XBee / XBee-PRO)
0 - 0x50 [-dBm]
0 = -10 / 10 dBm
1 = -6 / 12 dBm
2 = -4 / 14 dBm
3 = -2 / 16 dBm
4 = 0 / 18 dBm
Default
-
-
0 (disabled)
-
Default
4
0x2C
(-44d dBm)
27