XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 35

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
CC (Command Sequence Character) Command
CE (Coordinator Enable) Command
CH (Channel) Command
CN (Exit Command Mode) Command
CT (Command Mode Timeout) Command
<AT Command Mode Options> The CC command
is used to set and read the ASCII character used
between guard times of the AT Command Mode
Sequence (GT + CC + GT). This sequence enters
the RF modem into AT Command Mode so that
data entering the modem from the host is
recognized as commands instead of payload.
The AT Command Sequence is explained further in the AT Command Mode section.
<Serial Interfacing> The CE command is used to
set and read the behavior (End Device vs.
Coordinator) of the RF modem.
<Networking {Addressing}> The CH command is
used to set/read the operating channel on which
RF connections are made between RF modems.
The channel is one of three addressing options
available to the modem. The other options are
the PAN ID (ID command) and destination
addresses (DL & DH commands).
In order for modems to communicate with each
other, the modems must share the same channel number. Different channels can be used to
prevent modems in one network from listening to transmissions of another. Adjacent channel
rejection is 23 dB.
The modem uses channel numbers of the 802.15.4 standard.
Refer to the XBee/XBee-PRO Addressing section for more information.
<AT Command Mode Options> The CN command
is used to explicitly exit the RF modem from AT
Command Mode.
<AT Command Mode Options> The CT command
is used to set and read the amount of inactive
time that elapses before the RF modem
automatically exits from AT Command Mode and
returns to Idle Mode.
Use the CN (Exit Command Mode) command to
exit AT Command Mode manually.
Center Frequency = 2.405 + (CH - 11d) * 5 MHz
AT Command: ATCN
AT Command: ATCC
Parameter Range: 0 - 0xFF
Default Parameter Value: 0x2B (ASCII “+”)
Related Command: GT (Guard Times)
AT Command: ATCT
Parameter Range:2 - 0xFFFF
Default Parameter Value: 0x64 (100 decimal
(which equals 10 decimal seconds))
Number of bytes returned: 2
Related Command: CN (Exit Command Mode)
AT Command: ATCH
Parameter Range: 0x0C - 0x17
Default Parameter Value: 0x0C (12 decimal)
Related Commands: ID (PAN ID), DL
(Destination Address Low, DH (Destination
Address High)
AT Command: ATCE
Parameter Range:0 - 1
Default Parameter Value:0
Minimum Firmware Version Required: v1.x80
Parameter
(d = decimal)
0
1
[x 100 milliseconds]
Configuration
Coordinator
End Device
35