XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 48

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
SH (Serial Number High) Command
SL (Serial Number Low) Command
SM (Sleep Mode) Command
SP (Cyclic Sleep Period) Command
<Diagnostics> The SH command is used to read
the high 32 bits of the RF modem's unique IEEE
64-bit address.
The modem serial number is set at the factory
and is read-only.
<Diagnostics> The SL command is used to read
the low 32 bits of the RF modem's unique IEEE
64-bit address.
The modem serial number is set at the factory
and is read-only.
<Sleep Mode (Low Power)> The SM command is
used to set and read Sleep Mode settings. By
default, Sleep Modes are disabled (SM = 0) and
the RF modem remains in Idle/Receive Mode.
When in this state, the modem is constantly
ready to respond to either serial or RF activity.
SM command options vary according to the
networking system type. By default, the modem
is configured to operate in a NonBeacon system.
* The Sleep Coordinator option (SM=6) only
exists for backwards compatibility with firmware
version 1.x06 only. In all other cases, use the CE
command to enable a Coordinator.
<Sleep Mode (Low Power)> The SP command is
used to set and read the duration of time in which
a remote RF modem sleeps. After the cyclic sleep
period is over, the modem wakes and checks for
data. If data is not present, the modem goes back
to sleep. The maximum sleep period is 268
seconds (SP = 0x68B0).
The SP parameter is only valid if the modem is
configured to operate in Cyclic Sleep (SM = 4-6).
Coordinator and End Device SP values should
always be equal.
To send Direct Messages, set SP = 0.
NonBeacon Firmware
End Device - SP determines the sleep period for cyclic sleeping remotes. Maximum sleep period is
268 seconds (0x68B0).
Coordinator - If non-zero, SP determines the time to hold an indirect message before discarding it.
A Coordinator will discard indirect messages after a period of (2.5 * SP).
AT Command: ATSP
Parameter
Range:
Default
Parameter
Value:
Related Commands: SM (Sleep Mode), ST
(Time before Sleep), DP (Disassociation Cyclic
Sleep Period, BE (Beacon Order)
AT Command: ATSM
Parameter Range: 0 - 6
Default Parameter Value: 0
Related Commands: SP (Cyclic Sleep Period),
ST (Time before Sleep)
AT Command: ATSH
Parameter Range: 0 - 0xFFFFFFFF [read-only]
Related Commands: SL (Serial Number Low),
MY (Source Address)
AT Command: ATSL
Parameter Range: 0 - 0xFFFFFFFF [read-only]
Related Commands: SH (Serial Number High),
MY (Source Address)
Parameter
NonBeacon Firmware:
1 - 0x68B0 [x 10 milliseconds]
NonBeacon Firmware: 0
0
1
2
3
4
5
6
Cyclic Sleep Remote
Cyclic Sleep Remote
(with Pin Wake-up)
Sleep Coordinator*
Configuration
Pin Hibernate
(reserved)
Disabled
Pin Doze
48