XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 53

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
Identifies the UART data frame for the host to
correlate with a subsequent ACK (acknowledgement).
Setting Frame ID to ‘0' will disable response frame.
Identifies the UART data frame for the host to
correlate with a subsequent ACK (acknowledgement).
Setting Frame ID to ‘0' will disable response frame.
Frame ID (Byte 5)
Frame ID (Byte 5)
Identifies the UART data frame being reported .
Note: If Frame ID = 0 in AT Command Mode,
no AT Command Response will be given.
AT Command Response
TX (Transmit) Request: 64-bit address
TX (Transmit) Request: 16-bit address
Start Delimiter
Start Delimiter
0x7E
API Identifier Value: 0x88
Response to previous command.
In response to an AT Command message, the modem will send an AT Command Response
message. Some commands will send back multiple frames (for example, the ND (Node Discover)
and AS (Active Scan) commands). These commands will end by sending a frame with a status of
ATCMD_OK and no cmdData.
Figure 4‐011.AT Command Response Frames.
API Identifier Value: 0x00
A TX Request message will cause the modem to send RF Data as an RF Packet.
Figure 4‐12. TX Packet (64‐bit address) Frames
API Identifier Value: 0x01
A TX Request message will cause the modem to send RF Data as an RF Packet.
Figure 4‐13. TX Packet (16‐bit address) Frames
0x7E
Start Delimiter
0x7E
Frame ID (Byte 5 )
MSB
MSB
Length
MSB
Length
LSB
Length
Destination Address (Bytes 6-13)
API Identifier
LSB
MSB first, LSB last.
Broadcast =
0x000000000000FFFF
LSB
Destination Address (Bytes 6-7)
0x00
API Identifier
API Identifier
MSB first, LSB last.
Broadcast = 0xFFFF
0x01
0x88
API-specific Structure
API-specific Structure
API-specific Structure
Frame Data
Command Name - Two
ASCII characters that
identify the AT Command .
Frame Data
AT Command (Bytes 6-7)
Frame Data
Identifier-specific Data
Identifier-specific Data
Identifier-specific Data
cmdData
cmdData
cmdData
0x01 = Disable ACK
0x04 = Send packet with Broadcast Pan ID
All other bits must be set to 0.
Checksum
Checksum
1 Byte
1 Byte
0x01 = Disable ACK
0x04 = Send packet with Broadcast Pan ID
All other bits must be set to 0.
Checksum
1 Byte
Status (Byte 8)
0 = OK
1 = ERROR
2 = Invalid Command
3 = Invalid Parameter
Options (Byte 14)
Options (Byte 8)
The HEX (non -ASCII) value
of the requested register
Value (Byte(s) 9-n)
Up to 100 Bytes per packet
RF Data (Byte(s) 15-n)
Up to 100 Bytes per p
RF Data (Byte(s) 9-n)
53