XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 40

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
FR (Software Reset) Command
GT (Guard Times) Command
HV (Hardware Version) Command
IA (I/O Input Address) Command
IC (DIO Change Detect) Command
ID (Pan ID) Command
<Special> The FR command is used to force a
software reset on the RF modem. The reset
simulates powering off and then on again the
modem.
<AT Command Mode Options> GT Command is
used to set the DI (data in from host) time-of-
silence that surrounds the AT command sequence
character (CC Command) of the AT Command
Mode sequence (GT + CC + GT).
The DI time-of-silence is used to prevent
inadvertent entrance into AT Command Mode.
Refer to the Command Mode section for more
information regarding the AT Command Mode Sequence.
<Diagnostics> The HV command is used to read
the hardware version of the RF modem.
<I/O Settings {I/O Line Passing}> The IA
command is used to bind a modem output to a
specific address. Outputs will only change if
received from this address. The IA command can
be used to set/read both 16 and 64-bit
addresses.
Setting all bytes to 0xFF will not allow the
reception of any I/O packet to change outputs.
Setting the IA address to 0xFFFF will cause the modem to accept all I/O packets.
<I/O Settings> Set/Read bitfield values for
change detect monitoring. Each bit enables
monitoring of DIO0 - DIO7 for changes.
If detected, data is transmitted with DIO data
only. Any samples queued waiting for
transmission will be sent first.
Refer to the “ADC and Digital I/O Line Support” sections of the “RF Modem Operations” chapter for
more information.
<Networking {Addressing}> The ID command is
used to set and read the PAN (Personal Area
Network) ID of the RF modem. Only modems with
matching PAN IDs can communicate with each
other. Unique PAN IDs enable control of which RF
packets are received by a modem.
Setting the ID parameter to 0xFFFF indicates a global transmission for all PANs. It does not
indicate a global receive.
AT Command: ATHV
Parameter Range:0 - 0xFFFF [Read-only]
Minimum Firmware Version Required: v1.x80
AT Command: ATFR
Minimum Firmware Version Required: v1.x80
AT Command: ATGT
Parameter Range:2 - 0x0CE4
Default Parameter Value:0x3E8
Related Command: CC (Command Sequence
Character)
AT Command: ATIA
Parameter Range:0 - 0xFFFFFFFFFFFFFFFF
Default Parameter Value:0xFFFFFFFFFFFFFFFF
(will not allow any received I/O packet to
change outputs)
Minimum Firmware Version Required: v1.xA0
AT Command: ATID
Parameter Range: 0 - 0xFFFF
Default Parameter Value:0x3332
AT Command: ATIC
Parameter Range:0 - 0xFF [bitfield]
Default Parameter Value:0 (disabled)
Minimum Firmware Version Required: 1.xA0
[x 1 millisecond]
(1000 decimal)
(13106 decimal)
40