XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 33

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
AP (API Enable) Command
AS (Active Scan) Command
<Serial Interfacing> The AP command is used to
enable the RF modem to operate using a frame-
based API instead of using the default
Transparent (UART) mode.
Refer to the API Operation section [p50] when API operation is enabled (AP = 1 or 2).
<AT Command Mode Options> The AS command
is used to send a Beacon Request to a Broadcast
Address (0xFFFF) and Broadcast PAN (0xFFFF) on
every channel. The parameter determines the
amount of time the RF modem will listen for
Beacons on each channel. A ‘PanDescriptor’ is
created and returned for every Beacon received
from the scan. Each PanDescriptor contains the
following information:
CoordAddress (SH + SL parameters)<CR>
CoordPanID (ID parameter)<CR>
CoordAddrMode <CR>
Channel (CH parameter) <CR>
SecurityUse<CR>
ACLEntry<CR>
SecurityFailure<CR>
SuperFrameSpec<CR> (2 bytes):
GtsPermit<CR>
RSSI<CR> (- RSSI is returned as -dBm)
TimeStamp<CR> (3 bytes)
<CR> (A carriage return <CR> is sent at the end of the AS command.
The Active Scan is capable of returning up to 5 PanDescriptors in a scan. The actual scan time on
each channel is measured as Time = [(2 ^ (SD Parameter)) * 15.36] ms. Total scan time is this
time multiplied by the number of channels to be scanned (16 for the XBee, 12 for the XBee-PRO).
NOTE: Refer the scan table in the SD description to determine scan times. If using API Mode, no
<CR>’s are returned in the response. Refer to the API Mode Operation section [p50].
0x02 = 16-bit Short Address
0x03 = 64-bit Long Address
bit 15 - Association Permitted (MSB)
bit 14 - PAN Coordinator
bit 13 - Reserved
bit 12 - Battery Life Extension
bits 8-11 - Final CAP Slot
bits 4-7 - Superframe Order
bits 0-3 - Beacon Order
AT Command: ATAS
Parameter Range: 0 - 6
Related Command: SD (Scan Duration), DL
(Destination Low Address), DH (Destination
High Address), ID (PAN ID), CH (Channel)
Minimum Firmware Version Required: v1.x80
AT Command: ATAP
Parameter Range:0 - 2
Default Parameter Value:0
Minimum Firmware Version Required: v1.x80
Parameter
0
1
2
(Transparent operation)
Configuration
(with escaped
API enabled
API enabled
characters)
Disabled
33