XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 32

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
AC (Apply Changes) Command
AI (Association Indication) Command
<AT Command Mode Options> The AC command
is used to explicitly apply changes to modem
parameter values. ‘Applying changes’ means that
the modem is re-initialized based on changes
made to its parameter values. Once changes are applied, the modem immediately operates
according to the new parameter values.
This behavior is in contrast to issuing the WR (Write) command. The WR command saves
parameter values to non-volatile memory, but the modem still operates according to previously
saved values until the modem is re-booted or the CN (Exit AT Command Mode) command is
issued.
Refer to the “AT Command - Queue Parameter Value” API type for more information [p52].
<Networking {Association}> The AI command is
used to indicate occurrences of errors during the
last association request.
Use the table below to determine meaning of the
returned values.
Returned Value (Hex) Association Indication
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
Successful Completion - Coordinator successfully started or End Device association complete
Active Scan Timeout
Active Scan found no PANs
Active Scan found PAN, but the Coordinator Allow Association bit is not set
Active Scan found PAN, but Coordinator and End Device are not configured to support beacons
Active Scan found PAN, but Coordinator ID (PAN ID) value does not match the ID of the End Device
Active Scan found PAN, but Coordinator CH (Channel) value does not match the CH of the End Device
Energy Scan Timeout
Coordinator start request failed
Coordinator could not start due to Invalid Parameter
Coordinator Realignment is in progress
Association Request not sent
Association Request timed out - no reply was received
Association Request had an Invalid Parameter
Association Request Channel Access Failure - Request was not transmitted - CCA failure
Remote Coordinator did not send an ACK after Association Request was sent
Remote Coordinator did not reply to the Association Request, but an ACK was received
after sending the request
[reserved]
Sync-Loss - Lost synchronization with a Beaconing Coordinator
Disassociated - No longer associated to Coordinator
AT Command: ATAC
Minimum Firmware Version Required: v1.xA0
AT Command: ATAI
Parameter Range: 0 - 0x13 [read-only]
Related Commands: AS (Active Scan), ID (PAN
ID), CH (Channel), ED (Energy Scan), A1 (End
Device Association), A2 (Coordinator
Association), CE (Coordinator Enable)
Minimum Firmware Version Required: v1.x80
32