XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 49

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
ST (Time before Sleep) Command
T0 - T7 ((D0-D7) Output Timeout) Command
VL (Firmware Version - Verbose)
VR (Firmware Version) Command
WR (Write) Command
<Sleep Mode (Low Power)> The ST command is
used to set and read the period of inactivity (no
serial or RF data is sent or received) before
activating Sleep Mode.
NonBeacon Firmware
Set/Read time period of inactivity (no serial or RF
data is sent or received) before activating Sleep
Mode. ST parameter is only valid with Cyclic
Sleep settings (SM = 4 - 5).
Coordinator and End Device ST values must be equal.
<I/O Settings {I/O Line Passing}> The T0, T1,
T2, T3, T4, T5, T6 and T7 commands are used to
set/read output timeout values for the lines that
correspond with the D0 - D7 parameters. When
output is set (due to I/O line passing) to a non-
default level, a timer is started which when
expired, will set the output to its default level. The timer is reset when a valid I/O packet is
received. The Tn parameter defines the permissible amount of time to stay in a non-default
(active) state. If Tn = 0, Output Timeout is disabled (output levels are held indefinitely).
<Diagnostics> The VL command is used to read
detailed version information about the RF
modem. The information includes:
application build date; MAC, PHY and bootloader
versions; and build dates.
<Diagnostics> The VR command is used to read
which firmware version is stored in the modem.
XBee version numbers will have four significant
digits. The reported number will show three or four numbers and is stated in hexadecimal
notation. A version can be reported as "ABC" or "ABCD". Digits ABC are the main release number
and D is the revision number from the main release. "D" is not required and if it is not present, a
zero is assumed for D. "B" is a variant designator. The following variants exist:
<(Special)> The WR command is used to write
configurable parameters to the RF modem's non-
volatile memory. Parameter values remain in the
modem's memory until overwritten by subsequent use of the WR Command.
If changes are made without writing them to non-volatile memory, the modem reverts back to
previously saved parameters the next time the modem is powered-on.
NOTE: Once the WR command is sent to the modem, no additional characters should be sent until
after the “OK/r” response is received.
• "0" = Non-Beacon Enabled 802.15.4 Code
• "1" = Beacon Enabled 802.15.4 Code
AT Command: ATST
Parameter
Range:
Default
Parameter
Value:
Related Commands: SM (Sleep Mode), ST
(Time before Sleep)
AT Command: ATWR
AT Command: ATVR
Parameter Range: 0 - 0xFFFF [read only]
AT Command: ATVL
Parameter Range:0 - 0xFF
Default Parameter Value: 0x28 (40 decimal)
Minimum Firmware Version Required: v1.x80
AT Commands: ATT0 - ATT7
Parameter Range:0 - 0xFF [x 100 msec]
Default Parameter Value:0xFF
Minimum Firmware Version Required: v1.xA0
NonBeacon Firmware:
1 - 0xFFFF [x 1 millisecond]
NonBeacon Firmware: 0x1388
(5000 decimal)
[x 100 milliseconds]
49