CY7C68001-56LTXC Cypress Semiconductor Corp, CY7C68001-56LTXC Datasheet - Page 47

• Manufacturer Part Number: CY7C68001-56LTXC
• Description: IC USB EZ-USB SX2 HS 56VQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: CY7Cr
• Type: USBr

Specifications of CY7C68001-56LTXC

• Protocol: USB 2.0
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-2932

13.0
The following recommendations should be followed to ensure reliable high-performance operation.
14.0
Electrical contact of the part to the Printed Circuit Board (PCB) is made by soldering the leads on the bottom surface of the
package to the PCB. Hence, special attention is required to the heat transfer area below the package to provide a good thermal
bond to the circuit board. A Copper (Cu) fill is to be designed into the PCB as a thermal pad under the package. Heat is transferred
from the SX2 through the device’s metal paddle on the bottom side of the package. Heat from here, is conducted to the PCB at
the thermal pad. It is then conducted from the thermal pad to the PCB inner ground plane by a 5 x 5 array of via. A via is a plated
through hole in the PCB with a finished diameter of 13 mil. The QFN’s metal die paddle must be soldered to the PCB’s thermal
pad. Solder mask is placed on the board top side over each via to resist solder flow into the via. The mask on the top side also
minimizes outgassing during the solder reflow process.
For further information on this package design please refer to the application note “Surface Mount Assembly of AMKOR’s
MicroLeadFrame (MLF) Technology.” This application note can be downloaded from AMKOR’s website from the following URL
http://www.amkor.com/products/notes_papers/MLF_AppNote_0902.pdf. The application note provides detailed information on
board mounting guidelines, soldering flow, rework process, etc.
Figure 14-1 below display a cross-sectional area underneath the package. The cross section is of only one via. The solder paste
template needs to be designed to allow at least 50% solder coverage. The thickness of the solder paste template should be 5 mil.
It is recommended that “No Clean” type 3 solder paste is used for mounting the part. Nitrogen purge is recommended during
reflow.
Figure 14-2a is a plot of the solder mask pattern and Figure 14-2b displays an X-Ray image of the assembly (darker areas indicate
solder.
Notes:
Document #: 38-08013 Rev. *B
2.
• At least a four-layer impedance controlled boards are required to maintain signal quality.
• Specify impedance targets (ask your board vendor what they can achieve).
• To control impedance, maintain trace widths and trace spacing.
• Minimize stubs to minimize reflected signals.
• Connections between the USB connector shell and signal ground must be done near the USB connector.
• Bypass/flyback caps on VBus, near connector, are recommended.
• DPLUS and DMINUS trace lengths should be kept to within 2 mm of each other in length, with preferred length of 20–30 mm.
• Maintain a solid ground plane under the DPLUS and DMINUS traces. Do not allow the plane to be split under these traces.
• It is preferred to have no vias placed on the DPLUS or DMINUS trace routing.
• Isolate the DPLUS and DMINUS traces from all other signal traces by no less than 10 mm.
Source for recommendations: High-Speed USB Platform Design Guidelines, http://www.usb.org/developers/data/hs_usb_pdg_r1_0.pdf.
Figure 14-2. (a) Plot of the Solder Mask (White Area)
General PCB Layout Guidelines
Quad Flat Package No Leads (QFN) Package Design Notes
Via hole for thermally connecting the
QFN to the circuit board ground plane.
Figure 14-1. Crosssection of the Area Underneath the QFN Package
PCB Material
Cu Fill
[2]
Solder Mask
0.013” dia
0.017” dia
This figure only shows the top three layers of the
circuit board: Top Solder, PCB Dielectric, and the Ground Plane.
Cu Fill
Figure 0-1. (b) X-ray Image of the Assembly
PCB Material
CY7C68001
Page 47 of 50