PEB20256EV21GXP Infineon Technologies, PEB20256EV21GXP Datasheet - Page 115
PEB20256EV21GXP
Manufacturer Part Number
PEB20256EV21GXP
Description
Manufacturer
Infineon Technologies
Datasheet
1.PEB20256EV21GXP.pdf
(232 pages)
Specifications of PEB20256EV21GXP
Operating Supply Voltage (typ)
2.5/3.3V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Lead Free Status / Rohs Status
Compliant
- Current page: 115 of 232
- Download datasheet (3Mb)
6
For channel programming the MUNICH256 provides a on-chip channel specification
data structure. All information necessary to setup a channel has to be provided using this
data structure. As soon as all channel information has been written to the channel
specification registers the information can be released using simple channel commands,
which have to be written to register CSPEC_CMD. The relevant channel information will
then be copied to the chip internal channel database. The channel specification
registers, which need to be programmed before a command can be executed, are shown
in Table 6-1.
Before initializing a channel the time slot assignment process for the affected channel
must be completed. Vice versa after shutting down a channel the time slots associated
with the affected channel should be set to inhibit. Otherwise if a time slot is
reprogrammed afterwards, strange behavior can be expected on the serial side.
For each channel a simple sequence of channel commands must be ensured. After reset
each channel is in its ’off’ state. Therefore, the first command to start a channel is
’Transmit Init’ or ’Receive Init’. This brings the channel into the operational state. In this
state all commands except ’Transmit Init’, ’Receive Init’ or ’Transmit Idle can be given.
To bring a channel back into the idle state a ’Transmit Off’ or ’Receive Off’ command has
to be programmed. For certain channel commands system software has to wait before
new commands can be given for the same channel. This is due to internal buffer
allocation functions which require some processing time. Notification of system software
is done in form of command interrupt vectors, which signal that a command has
successful or even unsuccessful completed.
Table 6-1
Register
CSPEC_MODE_REC
CSPEC_REC_ACCM
CSPEC_MODE_XMIT
Data Sheet
Channel Programming / Reprogramming Concept
Channel Specification Registers and Channel Commands
Channel Programming / Reprogramming Concept
Transmit Commands
115
Receive
Commands
PEB 20256 E
PEF 20256 E
04.2001
Related parts for PEB20256EV21GXP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Multichannel Network Interface Controller for HDLC/PPP with 256 Channels
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
IC CONTROLLER INTERFACE 388-BGA
Manufacturer:
Infineon Technologies
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
16-bit microcontroller with 2x2 KByte RAM
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Si-MMIC-amplifier in SIEGET 25-technologie
Manufacturer:
Infineon Technologies AG
Datasheet: