AT32UC3A0128 Atmel Corporation, AT32UC3A0128 Datasheet - Page 240

• Manufacturer Part Number: AT32UC3A0128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A0128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 109
• Ext Interrupts: 109
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
24.13.5
24.13.5.1
Figure 24-23. Read Access Ordered by a MASTER
24.13.5.2
EOSVACC
SVREAD
TXRDY
SVACC
NACK
TWD
Data Transfer
Read Operation
Write Operation
S
ADR
TWI answers with a NACK
SADR does not match,
As it is impossible to know the exact number of data to receive/send, the use of PDC is NOT rec-
ommended in SLAVE mode.
The read mode is defined as a data requirement from the master.
After a START or a REPEATED START condition is detected, the decoding of the address
starts. If the slave address (SADR) is decoded, SVACC is set and SVREAD indicates the direc-
tion of the transfer.
Until a STOP or REPEATED START condition is detected, TWI continues sending data loaded
in the THR register.
If a STOP condition or a REPEATED START + an address different from SADR is detected,
SVACC is reset.
Figure 24-23 on page 240
Notes:
The write mode is defined as a data transmission from the master.
After a START or a REPEATED START, the decoding of the address starts. If the slave address
is decoded, SVACC is set and SVREAD indicates the direction of the transfer (SVREAD is low in
this case).
Until a STOP or REPEATED START condition is detected, TWI stores the received data in the
RHR register.
If a STOP condition or a REPEATED START + an address different from SADR is detected,
SVACC is reset.
Figure 24-24 on page 241
R
NA
1. When SVACC is low, the state of SVREAD becomes irrelevant.
2. TXRDY is reset when data has been transmitted from THR to the shift register and set when
DATA
this data has been acknowledged or non acknowledged.
NA
P/S/Sr
describes the write operation.
describes the Write operation.
Write THR
SADR
TWI answers with an ACK
SADR matches,
R
SVREAD has to be taken into account only while SVACC is active
A
DATA
A
ACK/NACK from the Master
A
DATA
AT32UC3A
NA
S/Sr
Read RHR
240