AT32UC3A0128 Atmel Corporation, AT32UC3A0128 Datasheet - Page 242

• Manufacturer Part Number: AT32UC3A0128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A0128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 109
• Ext Interrupts: 109
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
24.13.6
24.13.6.1
Figure 24-26. Clock Synchronization in Read Mode
Notes:
TWI_THR
TXCOMP
SVREAD
SCLWS
SVACC
TXRDY
TWCK
1. TXRDY is reset when data has been written in the TH to the shift register and set when this data has been acknowledged or
2. At the end of the read sequence, TXCOMP is set after a STOP or after a REPEATED_START + an address different from
3. SCLWS is automatically set when the clock synchronization mechanism is started.
Clock Synchronization
non acknowledged.
SADR.
Clock Synchronization in Read Mode
1
2
S
S
The data is memorized in TWI_THR until a new value is written
TWI_THR is transmitted to the shift register
The clock is stretched after the ACK, the state of TWD is undefined during clock stretching
As soon as a START is detected
SADR
In both read and write modes, it may happen that THR/RHR buffer is not filled /emptied before
the emission/reception of a new character. In this case, to avoid sending/receiving undesired
data, a clock stretching mechanism is implemented.
The clock is tied low if the shift register is empty and if a STOP or REPEATED START condition
was not detected. It is tied low until the shift register is loaded.
Figure 24-26 on page 242
D D D A A A T T T A A A 0 0 0
R
Write THR
A
1
DATA0
A
describes the clock synchronization in Read mode.
DATA1
DATA1
CLOCK is tied low by the TWI
as long as THR is empty
A
XXXXXXX
2
DATA2
DATA2
Ack or Nack from the master
NA
AT32UC3A
S
242