ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 181

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

15.6.1
8265B–AVR–09/10
LINCR – LIN Control Register
• Bit 7 – LSWRES: Software Reset
• Bit 6 – LIN13: LIN 1.3 mode
• Bits 5:4 – LCONF[1:0]: Configuration
• Bit 3 – LENA: Enable
• Bits 2:0 – LCMD[2:0]: Command and mode
Bit
(0xC8)
Read/Write
Initial Value
– 0 = No action,
– 1 = Software reset (this bit is self-reset at the end of the reset procedure).
– 0 = LIN 2.1 (default),
– 1 = LIN 1.3.
a. LIN mode (default = 00):
– 00 = LIN Standard configuration (listen mode “off”, CRC “on” & Frame_Time_Out
– 01 = No CRC, No Frame_Time_Out (listen mode “off”),
– 10 = No Frame_Time_Out (listen mode “off” & CRC “on”),
– 11 = Listening mode (CRC “on” & Frame_Time_Out “on”).
b. UART mode (default = 00):
– 00 = 8-bit, no parity (listen mode “off”),
– 01 = 8-bit, even parity (listen mode “off”),
– 10 = 8-bit, odd parity (listen mode “off”),
– 11 = Listening mode, 8-bit, no parity.
– 0 = Disable (both LIN and UART modes),
– 1 = Enable (both LIN and UART modes).
– 000 = LIN Rx Header - LIN abort,
– 001 = LIN Tx Header,
– 010 = LIN Rx Response,
– 011 = LIN Tx Response,
– 100 = UART Rx & Tx Byte disable,
– 11x = UART Rx Byte enable,
– 1x1 = UART Tx Byte enable.
The command is only available if LENA is set.
“on”,
LSWRES
R/W
7
0
LIN13
R/W
6
0
LCONF1
R/W
5
0
LCONF0
R/W
4
0
LENA
R/W
3
0
LCMD2
R/W
2
0
LCMD1
R/W
1
0
LCMD0
R/W
0
0
LINCR
181