ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 227

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.2.1
21.3
8265B–AVR–09/10
Signature Bytes
Latching of Fuses
Table 21-5.
Notes:
The fuse values are latched when the device enters programming mode and changes of the
fuse values will have no effect until the part leaves Programming mode. This does not apply to
the EESAVE Fuse which will take effect once it is programmed. The fuses are also latched on
Power-up in Normal mode.
All Atmel microcontrollers have a three-byte signature code which identifies the device. This
code can be read in both serial and parallel mode, also when the device is locked. The three
bytes reside in a separate address space.
Table 21-6.
Fuse Low Byte
CKDIV8
CKOUT
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
Device
ATtiny87
ATtiny167
1. The default value of SUT[1:0] results in maximum start-up time for the default clock source.
2. The default setting of CKSEL[3:0] results in internal RC Oscillator @ 8 MHz. See
3. The CKOUT Fuse allows the system clock to be output on PORTB5.
4.
(3)
(4)
See
on page 27
fer” on page 31.
See ”System Clock Prescaler” on page
Fuse Low Byte
Signature Bytes
Table 4-4 on page 27
Bit No
Address
for details.
7
6
5
4
3
2
1
0
0
1
2
0
1
2
for details.
Description
Divide clock by 8
Clock output
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
Value
0x1E
0x1E
0x93
0x87
0x94
0x87
for details.
Signature Byte Description
Indicates manufactured by Atmel
Indicates 8 KB Flash memory
Indicates ATtiny87 device when address 1 contains
0x93
Indicates manufactured by Atmel
Indicates 16 KB Flash memory
Indicates ATtiny167 device when address 1 contains
0x94
37.for details.
0 (programmed)
1 (unprogrammed)
1 (unprogrammed)
0 (programmed)
1 (unprogrammed)
Default Value
0 (programmed)
0 (programmed)
0 (programmed)
See ”Clock Output Buf-
(1)
(2)
(2)
(2)
(1)
(2)
Table 4-3
227