ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 237

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.7.12
21.7.13
21.7.14
8265B–AVR–09/10
Reading the Fuse and Lock Bits
Reading the Signature Bytes
Reading the 8 MHz RC Oscillator Calibration Byte
The algorithm for reading the Fuse and Lock bits is as follows (refer to
Flash” on page 232
Figure 21-6. Mapping Between BS1, BS2 and the Fuse and Lock Bits During Read
The algorithm for reading the Signature bytes is as follows (refer to
on page 232
The algorithm for reading the 8 MHz RC Oscillator Calibration byte is as follows (refer to
gramming the Flash” on page 232
1. A: Load Command “0000 0100
2. Set OE to “0”, BS2 to “0” and BS1 to “0”. The status of the Fuse Low bits can now be
3. Set OE to “0”, BS2 to “1” and BS1 to “1”. The status of the Fuse High bits can now be
4. Set OE to “0”, BS2 to “1”, and BS1 to “0”. The status of the Extended Fuse bits can
5. Set OE to “0”, BS2 to “0” and BS1 to “1”. The status of the Lock bits can now be read
6. Set OE to “1”.
1. A: Load Command “0000 1000
2. B: Load Address Low Byte (0x00 - 0x02).
3. Set OE to “0”, and BS to “0”. The selected Signature byte can now be read at DATA.
4. Set OE to “1”.
1. A: Load Command “0000 1000
2. B: Load Address Low Byte, 0x00.
3. Set OE to “0”, and BS1 to “1”. The 8 MHz RC Oscillator Calibration byte can now be
4. Set OE to “1”.
read at DATA (“0” means programmed).
read at DATA (“0” means programmed).
now be read at DATA (“0” means programmed).
at DATA (“0” means programmed).
read at DATA.
for details on Command and Address loading):
Extended Fuse Byte
Fuse High Byte
Fuse Low Byte
for details on Command loading):
Lock Bits
BS2
BS2
for details on Command and Address loading):
b
b
b
”.
”.
”.
0
1
0
1
BS1
0
1
“Programming the Flash”
DATA
“Programming the
“Pro-
237