STM32W108CC STMicroelectronics, STM32W108CC Datasheet - Page 54

• Manufacturer Part Number: STM32W108CC
• Description: High-performance, IEEE 802.15.4 wireless system-on-chip with embedded Flash memory
• Manufacturer: STMicroelectronics

Specifications of STM32W108CC

• Receive Current (w/ Cpu): 27 mA
• Transmit Current (w/ Cpu, +3 Dbm Tx): 31 mA
• Low Deep Sleep Current, With Retained Ram And Gpio: 400 nA/800 nA with/without sleep timer
• Standard Arm Debug Capabilities: Flash patch & breakpoint; data watchpoint & trace; instrumentation trace macrocell
• Single Voltage Operation: 2.1-3.6 V with internal 1.8 V and 1.25 V regulators

System modules
6.5.3
6.5.4
54/232
In normal operation an application may request one of two low power modes through
program execution:
●
●
If a deep sleep is requested the STM32W108 first enters a pre-deep sleep state. This state
prevents any section of the chip from being powered off or reset until the SWJ goes idle (by
clearing CSYSPWRUPREQ). This pre-deep sleep state ensures debug operations are not
interrupted.
In the deep sleep state the STM32W108 waits for a wake up event which will return it to the
running state. In powering up the core logic the ARM® Cortex-M3 is put through a reset
cycle and ST software restores the stack and application state to the point where deep sleep
was invoked.
Further options for deep sleep
By default, the low-frequency internal RC oscillator (OSCRC) is running during deep sleep
(known as deep sleep 1).
To conserve power, OSCRC can be turned off during deep sleep. This mode is known as
deep sleep 2. Since the OSCRC is disabled, the sleep timer and watchdog timer do not
function and cannot wake the chip unless the low-frequency 32.768 kHz crystal oscillator is
used. Non-timer based wake sources continue to function. Once a wake event occurs, the
OSCRC restarts and becomes enabled.
Use of debugger with sleep modes
The debugger communicates with the STM32W108 using the SWJ.
When the debugger is connected, the CDBGPWRUPREQ bit in the debug port in the SWJ
is set, the STM32W108 will only enter deep sleep 0 (the Emulated Deep Sleep state). The
CDBGPWRUPREQ bit indicates that a debug tool is connected to the chip and therefore
there may be debug state in the system debug components. To maintain the state in the
system debug components only deep sleep 0 may be used, since deep sleep 0 will not
cause a power cycle or reset of the core domain. The CSYSPWRUPREQ bit in the debug
port in the SWJ indicates that a debugger wants to access memory actively in the
STM32W108. Therefore, whenever the CSYSPWRUPREQ bit is set while the STM32W108
is awake, the STM32W108 cannot enter deep sleep until this bit is cleared. This ensures the
STM32W108 does not disrupt debug communication into memory.
Idle Sleep is achieved by executing a WFI instruction whilst the SLEEPDEEP bit in the
Cortex System Control register (SCS_SCR) is clear. This puts the CPU into an idle
state where execution is suspended until an interrupt occurs. This is indicated by the
state at the bottom of the diagram. Power is maintained to the core logic of the
STM32W108 during the Idle Sleeping state.
Deep sleep is achieved by executing a WFI instruction with the SLEEPDEEP bit in
SCS_SCR set. This triggers the state transitions around the main loop of the diagram,
resulting in powering down the STM32W108's core logic, and leaving only the always-
on domain powered. Wake up is triggered when one of the pre-determined events
occurs.
STM32W108HB STM32W108CC STM32W108CB STM32W108CZ
Doc ID 16252 Rev 13