TMP86xy12MG Toshiba, TMP86xy12MG Datasheet - Page 83

• Manufacturer Part Number: TMP86xy12MG
• Manufacturer: Toshiba

Specifications of TMP86xy12MG

• Package: SSOP30
• Rom Types (m=mask,p=otp,f=flash): M/F
• Rom Size: 16
• Ram Size: 512
• Driver Led: 8
• Driver Lcd: -
• Spi/sio Channels: 1
• Uart/sio Channels: 1
• I2c/sio Channels: -
• High-speed Serial Output: -
• Adc 8-bit Channels: -
• Adc 10-bit Channels: 8
• Da Converter Channels: -
• Timer Counter 18-bit Channel: IGBT
• Timer Counter 16-bit Channel: 1
• Timer Counter 8-bit Channel: 2
• Motor Channels: -
• Watchdog Timer: Y
• Dual Clock: Y
• Clock Gear: -
• Number Of I/o Ports: 24
• Power Supply (v): 4.5 to 5.5

9.2 Control
Timer/Counter 7 Control Register 2
Timer/Counter 7 Control Register 3
TC7CR2
(002AH)
TC7CR3
(002BH)
Note: Due to the circuit configuration, a pulse shorter than 1/fc may be eliminated as noise or accepted as a trigger.
TC7CK
NCRSEL
PPG1INI
PPG2INI
TRGSEL
TRGAM
TC7OUT
CSTC
PPG1OE
PPG2OE
EMGIE
EMGR
EMGR
7
7
Select a source clock
(Supplied to the up counter).
Select the duration of noise elimination for
TC7 input
(after passing through the flip-flop).
Specify the initial
value of PPG1 out-
put.
Specify the initial
value of PPG2 out-
put.
Select a trigger start edge.
Trigger edge acceptance mode
Select an output waveform mode.
Select a count start mode.
Enable/disable PPG1 output.
Enable/disable PPG2 output.
Enable/disable input on the EMG pin.
Cancel the emergency output stop state.
EMGIE
6
6
PPG2OE
EMGF
Select positive or
negative logic.
5
5
PPG1OE
CNTBF
4
4
Page 72
00: fc
01: fc/2
10 fc/2
11: fc/2
00: Eliminate pulses shorter than 16/fc [s] as noise.
01: Eliminate pulses shorter than 8/fc [s] as noise.
10: Eliminate pulses shorter than 4/fc [s] as noise.
11: Do not eliminate noise. (Note)
0: Low (Positive logic)
1: High (Negative logic)
0: Low (Positive logic)
1: High (Negative logic)
0: Start on trigger falling edge.
1: Start on trigger rising edge.
0: Always accept trigger edges.
1: Do not accept trigger edges during active output.
00: PPG1/PPG2 independent output
01: –
10: Output with variable duty ratio
11: Output with 50% duty ratio
00: Command start and capture mode
01: Command start and trigger start mode.
10: Trigger start mode
11: -
0: Disable
1: Enable
0: Disable
1: Enable
0: Disable input.
1: Enable input.
0: -
1: Cancel the emergency output stop state.
CSIDIS
(Upon canceling the state,
this bit is automatically cleared to 0.)
3
3
2
3
CSTC
[Hz]
[Hz]
[Hz]
[Hz]
2
2
STM
1
1
TC7OUT
TC7ST
0
0
(Initial value: 0000 0000)
(Initial value: **00 0000)
TMP86CH12MG
R/W
R/W