tmp89fm82t TOSHIBA Semiconductor CORPORATION, tmp89fm82t Datasheet - Page 411

• Manufacturer Part Number: tmp89fm82t
• Description: 8 Bit Microcontroller
• Manufacturer: TOSHIBA Semiconductor CORPORATION

RA000
Table 22-12 Transfer Formats of the Product ID Code Output Command
BOOT
ROM
22.8.6
1st byte
2nd byte
3rd byte
4th byte
5th byte
6th byte
7th byte
8th byte
9th byte
10th byte
11th byte
12th byte
13th byte
14th byte (note 2)
15th byte (note 3)
16th byte (note 4)
17th byte (note 4)
18th byte (note 4
19th byte (note 4)
20th byte (note 4)
21st byte (note 4)
22nd byte (note 5)
23rd byte (note 5)
24th byte (note 5)
25th byte (note 5)
26th byte (note 5)
27th byte (note 5)
28th byte
29th byte
Note 1: "0xXX × 3" means that the device goes into an idle state after transmitting 3 bytes of 0xXX. For further information, refer
Note 2: The ROM size code at the 14th byte is shown in Table 22-13.
Note 3: Block count in 15th byte is different to that of erase block count in Sector erase.
Note 4: 16th through 21st bytes show the range of addresses in flash memory where data can be written.
Note 5: 22nd through 27th bytes show the flash memory area and RAM area that can be used by the RAM loader. Because the
Transfer byte
Table 22-12 shows the transfer formats of the product ID code output command.
Product ID code output command (operation command: 0xC0)
to Table 22-17.
range of addresses shown here does not include the work area used by BOOTROM, it is smaller than the size of a RAM
built into an actual product.
Matching data 1 (0x86 or 0x30)
-
Matching data 2 (0x79 or 0xCF)
-
Operation command data (0xC0)
-
(Wait for the next operation command data) Baud rate after adjustment
Transfer data from the external controller to
TMP89FM82T
Page 395
Automatic adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate after adjustment
Baud rate
-(Automatic baud rate adjustment)
OK: Echo back data (0x86 or 0x30)
Error: No data transmitted
-
OK: Echo back data (0x79 or 0xCF)
Error: No data transmitted
-
OK: Echo back data (0xC0)
Error: 0xA1 × 3, 0xA3 × 3, 0x63 × 3 (note 1)
Transfer data from TMP89FM82T to the external
0xFD
0xYY
0x3A
0xFF
0xFF
0x3F
0x13
0x03
0x01
0x00
0x01
0x80
0x01
0x00
0x80
0x00
0x00
0x00
0x00
0x60
0x00
0x08
Start mark
Number of transfer data (from 9th to
27th bytes)
Length of address (3 bytes)
Reserved
Reserved
Reserved
Reserved
ROM size code
ROM block count
(1 block)
First address of ROM (upper byte)
First address of ROM (middle byte)
First address of ROM (lower byte)
End address of ROM (upper byte)
End address of ROM (middle byte)
End address of ROM (lower byte)
First address of RAM (upper byte)
First address of RAM (middle byte)
First address of RAM (lower byte)
End address of RAM (upper byte)
End address of RAM (middle byte)
End address of RAM (lower byte)
YYH : Checksum of transfer data (com-
plement of 2 of the sum total from 9th
through 27th bytes)
controller
-
TMP89FM82T