MT47H32M16HR-25E AIT:G Micron, MT47H32M16HR-25E AIT:G Datasheet - Page 113

• Manufacturer Part Number: MT47H32M16HR-25E AIT:G
• Description: DRAM Chip DDR2 SDRAM 512M-Bit 32Mx16 1.8V 84-Pin FBGA
• Manufacturer: Micron

Power-Down Mode
PDF: 09005aef8440dbbc
512mbddr2_ait_aat.pdf – Rev. C 7/11 EN
DDR2 SDRAM supports multiple power-down modes that allow significant power sav-
ings over normal operating modes. CKE is used to enter and exit different power-down
modes. Power-down entry and exit timings are shown in Figure 67 (page 114). Detailed
power-down entry conditions are shown in Figure 68 (page 116)–Figure 75 (page 119).
Table 43 (page 115) is the CKE Truth Table.
DDR2 SDRAM requires CKE to be registered HIGH (active) at all times that an access is
in progress—from the issuing of a READ or WRITE command until completion of the
burst. Thus, a clock suspend is not supported. For READs, a burst completion is defined
when the read postamble is satisfied; for WRITEs, a burst completion is defined when
the write postamble and
READ command) are satisfied, as shown in Figure 70 (page 117) and Figure 71
(page 117) on Figure 71 (page 117). The number of clock cycles required to meet
is either two or
Power-down mode (see Figure 67 (page 114)) is entered when CKE is registered low co-
incident with an NOP or DESELECT command. CKE is not allowed to go LOW during a
mode register or extended mode register command time, or while a READ or WRITE op-
eration is in progress. If power-down occurs when all banks are idle, this mode is refer-
red to as precharge power-down. If power-down occurs when there is a row active in
any bank, this mode is referred to as active power-down. Entering power-down deacti-
vates the input and output buffers, excluding CK, CK#, ODT, and CKE. For maximum
power savings, the DLL is frozen during precharge power-down. Exiting active power-
down requires the device to be at the same voltage and frequency as when it entered
power-down. Exiting precharge power-down requires the device to be at the same volt-
age as when it entered power-down; however, the clock frequency is allowed to change
(see Precharge Power-Down Clock Frequency Change (page 120)).
The maximum duration for either active or precharge power-down is limited by the re-
fresh requirements of the device
entry and exit is limited by the
tained while in power-down mode: CKE LOW, a stable clock signal, and stable power
supply signals at the inputs of the DDR2 SDRAM. All other input signals are “Don’t
Care” except ODT. Detailed ODT timing diagrams for different power-down modes are
shown in Figure 80 (page 125)–Figure 85 (page 129).
The power-down state is synchronously exited when CKE is registered HIGH (in con-
junction with a NOP or DESELECT command), as shown in Figure 67 (page 114).
Micron Confidential and Proprietary
t
WTR/
t
CK, whichever is greater.
t
WR (WRITE-to-PRECHARGE command) or
113
512Mb: x8, x16 Automotive DDR2 SDRAM
t
CKE (MIN) parameter. The following must be main-
t
RFC (MAX). The minimum duration for power-down
Micron Technology, Inc. reserves the right to change products or specifications without notice.
Power-Down Mode
‹ 2010 Micron Technology, Inc. All rights reserved.
t
WTR (WRITE-to-
t
WTR