DS3172 Maxim Integrated, DS3172 Datasheet - Page 103
DS3172
Manufacturer Part Number
DS3172
Description
Network Controller & Processor ICs Dual DS3/E3 Single Chip Transceiver
Manufacturer
Maxim Integrated
Datasheet
1.DS3171.pdf
(234 pages)
Specifications of DS3172
Part # Aliases
90-31720-000
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 103 of 234
- Download datasheet (2Mb)
stored in the highest numbered bit (5). This is to differentiate between a code in a register and the corresponding
code in a signal.
10.9.3.1 Transmit Data Storage
The Transmit Data Storage block contains the registers for two FEAC codes (C{1:6]) and controller circuitry for
reading and writing the memory. The Transmit Data Storage receives data from the microprocessor interface, and
stores the data in memory. The Transmit FEAC Processor reads the data from the Transmit Data Storage.
10.9.3.2 Transmit FEAC Processor
The Transmit FEAC Processor accepts data from the Transmit Data Storage performs FEAC processing. The
FEAC codes are read from Transmit Data Storage with the MSB (C[1]) in TFCA[0] or TFCB[0], and the LSB (C[6])
in TFCA[5] or TFCB[5].
FEAC processing has four modes of operation (Idle, single code, dual code, and continuous code). In Idle mode, all
ones are output on the outgoing FEAC data stream. In single code mode, the code from TFCA[5:0] is inserted into
a codeword (See
are output. In dual code mode, the code from TFCA[5:0] is inserted into a codeword, and sent ten consecutive
times. Then the code from TFCB[5:0] is inserted into a codeword, and sent ten consecutive times. Once both
codewords have both been sent ten times, all ones are output. In continuous mode, the code from TFCA[5:0] is
inserted into a codeword, and sent until the mode is changed
10.9.3.3 Receive FEAC Processor
The Receive FEAC Processor accepts an incoming data line and extracts all overhead and performs FEAC code
extraction , and Idle detection.
FEAC code extraction determines the codeword boundary by identifying the codeword sequence and extracts the
FEAC code. A FEAC codeword is a repeating 16-bit pattern (See
pattern (0xxxxxx011111111) that contains each FEAC code (C[6:1]). Each time slot is checked for a codeword
sequence. Once a codeword sequence is found, the FEAC code is checked. If the same FEAC code is received in
three consecutive codewords without errors, the FEAC code detection indication is set, and the FEAC code is
stored in the Receive FIFO with the MSB (C[1]) in RFF[0], and the LSB (C[6]) in RFF[5]. The FEAC code detection
indication is cleared if two consecutively received FEAC codewords differ from the current FEAC codeword, or a
FEAC Idle condition is detected.
Idle detection detects a FEAC Idle condition. A FEAC idle condition is declared if sixteen consecutive ones are
received. The FEAC Idle condition is terminated when the FEAC code detection indication is set.
10.9.3.4 Receive FEAC FIFO
The Receive FIFO block contains memory for four FEAC codes (C[1:6]) and controller circuitry for reading and
writing the memory. The Receive FIFO controller functions include filling the memory, tracking the memory fill level,
maintaining the memory read and write pointers, and detecting memory overflow and underflow conditions. The
Receive FIFO accepts data from the Receive FEAC Processor and stores the data in memory. The data is read
from the receive FIFO via the microprocessor interface. The Receive FIFO also outputs FIFO fill status (empty) via
the microprocessor interface. All operations are code based (six bits). The Receive FIFO is considered empty when
it does not contain any data. The Receive FIFO accepts data from the Receive FEAC Processor until full. If a
FEAC code is received while full, the data is discarded and a FIFO overflow condition is declared. If the Receive
FIFO is read while the FIFO is empty, the read is ignored.
Figure 10-24. FEAC Codeword Format
LSB
16
0
C6
C5 C4 C3 C2 C1
Figure
10-24), and sent ten consecutive times. Once the ten codewords have been sent, all ones
Receive/Transmit Order
Cx - FEAC Code
0
1
1
103
1
1
Figure
1
1
10-24). The codeword sequence is the
1
MSB
1
1
Related parts for DS3172
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: