C8051F587-IMR Silicon Labs, C8051F587-IMR Datasheet - Page 240
![no-image](/images/no-image-200.jpg)
C8051F587-IMR
Manufacturer Part Number
C8051F587-IMR
Description
8-bit Microcontrollers - MCU 50 MIPS 96 kB 8 kB SPI 2xUART
Manufacturer
Silicon Labs
Datasheet
1.C8051F585-IQR.pdf
(356 pages)
Specifications of C8051F587-IMR
Rohs
yes
Core
8051
Data Bus Width
8 bit
Processor Series
C8051
- Current page: 240 of 356
- Download datasheet (3Mb)
C8051F58x/F59x
overflow after 25 ms (and SMBTOE set), the Timer 3 interrupt service routine can be used to reset (disable
and re-enable) the SMBus in the event of an SCL low timeout.
23.3.5. SCL High (SMBus Free) Timeout
The SMBus specification stipulates that if the SCL and SDA lines remain high for more that 50 µs, the bus
is designated as free. When the SMBFTE bit in SMB0CF is set, the bus will be considered free if SCL and
SDA remain high for more than 10 SMBus clock source periods (as defined by the timer configured for the
SMBus clock source). If the SMBus is waiting to generate a Master START, the START will be generated
following this timeout. Note that a clock source is required for free timeout detection, even in a slave-only
implementation.
23.4. Using the SMBus
The SMBus can operate in both Master and Slave modes. The interface provides timing and shifting con-
trol for serial transfers; higher level protocol is determined by user software. The SMBus interface provides
the following application-independent features:
SMBus interrupts are generated for each data byte or slave address that is transferred. The point at which
the interrupt is generated depends on whether the hardware is acting as a data transmitter or receiver.
When a transmitter (i.e. sending address/data, receiving an ACK), this interrupt is generated after the ACK
cycle so that software may read the received ACK value; when receiving data (i.e. receiving address/data,
sending an ACK), this interrupt is generated before the ACK cycle so that software may define the outgo-
ing ACK value. See Section 23.5 for more details on transmission sequences.
Interrupts are also generated to indicate the beginning of a transfer when a master (START generated), or
the end of a transfer when a slave (STOP detected). Software should read the SMB0CN (SMBus Control
register) to find the cause of the SMBus interrupt. The SMB0CN register is described in Section 23.4.2;
Table 23.4 provides a quick SMB0CN decoding reference.
23.4.1. SMBus Configuration Register
The SMBus Configuration register (SMB0CF) is used to enable the SMBus Master and/or Slave modes,
select the SMBus clock source, and select the SMBus timing and timeout options. When the ENSMB bit is
set, the SMBus is enabled for all master and slave events. Slave events may be disabled by setting the
INH bit. With slave events inhibited, the SMBus interface will still monitor the SCL and SDA pins; however,
the interface will NACK all received addresses and will not generate any slave interrupts. When the INH bit
is set, all slave events will be inhibited following the next START (interrupts will continue for the duration of
the current transfer).
240
Byte-wise serial data transfers
Clock signal generation on SCL (Master Mode only) and SDA data synchronization
Timeout/bus error recognition, as defined by the SMB0CF configuration register
START/STOP timing, detection, and generation
Bus arbitration
Interrupt generation
Status information
Rev. 1.2
Related parts for C8051F587-IMR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![CP2102EK](/photos/9/3/90395/cp2102ek_tmb.jpg)
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CP2103EK](/photos/9/6/90669/cp2103ek_tmb.jpg)
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CP2201EK](/photos/9/9/90977/cp2201ek_tmb.jpg)
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CAPTOUCHSENSEDC](/photos/9/20/92001/captouchsensedc_tmb.jpg)
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CAPTOUCHSENSESK](/photos/9/20/92002/captouchsensesk_tmb.jpg)
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F320DK](/photos/9/20/92068/c8051f320dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F120DK](/photos/9/20/92070/c8051f120dk_tmb.jpg)
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F310DK](/photos/9/23/92300/c8051f310dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F226DK](/photos/9/23/92302/c8051f226dk_tmb.jpg)
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F300DK](/photos/9/23/92305/c8051f300dk_tmb.jpg)
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F330DK](/photos/9/23/92306/c8051f330dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F005DK](/photos/9/23/92307/c8051f005dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F020DK](/photos/9/23/92314/c8051f020dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F340DK](/photos/9/23/92323/c8051f340dk_tmb.jpg)
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F410DK](/photos/9/23/92324/c8051f410dk_tmb.jpg)
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: