C8051F587-IMR Silicon Labs, C8051F587-IMR Datasheet - Page 274
![no-image](/images/no-image-200.jpg)
C8051F587-IMR
Manufacturer Part Number
C8051F587-IMR
Description
8-bit Microcontrollers - MCU 50 MIPS 96 kB 8 kB SPI 2xUART
Manufacturer
Silicon Labs
Datasheet
1.C8051F585-IQR.pdf
(356 pages)
Specifications of C8051F587-IMR
Rohs
yes
Core
8051
Data Bus Width
8 bit
Processor Series
C8051
- Current page: 274 of 356
- Download datasheet (3Mb)
C8051F58x/F59x
26.3. SPI0 Slave Mode Operation
When SPI0 is enabled and not configured as a master, it will operate as a SPI slave. As a slave, bytes are
shifted in through the MOSI pin and out through the MISO pin by a master device controlling the SCK sig-
nal. A bit counter in the SPI0 logic counts SCK edges. When 8 bits have been shifted through the shift reg-
ister, the SPIF flag is set to logic 1, and the byte is copied into the receive buffer. Data is read from the
receive buffer by reading SPI0DAT. A slave device cannot initiate transfers. Data to be transferred to the
master device is pre-loaded into the shift register by writing to SPI0DAT. Writes to SPI0DAT are double-
buffered, and are placed in the transmit buffer first. If the shift register is empty, the contents of the transmit
buffer will immediately be transferred into the shift register. When the shift register already contains data,
the SPI will load the shift register with the transmit buffer’s contents after the last SCK edge of the next (or
current) SPI transfer.
When configured as a slave, SPI0 can be configured for 4-wire or 3-wire operation. The default, 4-wire
slave mode, is active when NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 1. In 4-wire mode, the
NSS signal is routed to a port pin and configured as a digital input. SPI0 is enabled when NSS is logic 0,
and disabled when NSS is logic 1. The bit counter is reset on a falling edge of NSS. Note that the NSS sig-
nal must be driven low at least 2 system clocks before the first active edge of SCK for each byte transfer.
Figure 26.4 shows a connection diagram between two slave devices in 4-wire slave mode and a master
device.
3-wire slave mode is active when NSSMD1 (SPI0CN.3) = 0 and NSSMD0 (SPI0CN.2) = 0. NSS is not
used in this mode, and is not mapped to an external port pin through the crossbar. Since there is no way of
uniquely addressing the device in 3-wire slave mode, SPI0 must be the only slave device present on the
bus. It is important to note that in 3-wire slave mode there is no external means of resetting the bit counter
that determines when a full byte has been received. The bit counter can only be reset by disabling and re-
enabling SPI0 with the SPIEN bit. Figure 26.3 shows a connection diagram between a slave device in 3-
wire slave mode and a master device.
26.4. SPI0 Interrupt Sources
When SPI0 interrupts are enabled, the following four flags will generate an interrupt when they are set to
logic 1:
All of the following bits must be cleared by software.
1. The SPI Interrupt Flag, SPIF (SPI0CN.7) is set to logic 1 at the end of each byte transfer. This flag can
2. The Write Collision Flag, WCOL (SPI0CN.6) is set to logic 1 if a write to SPI0DAT is attempted when
3. The Mode Fault Flag MODF (SPI0CN.5) is set to logic 1 when SPI0 is configured as a master, and for
4. The Receive Overrun Flag RXOVRN (SPI0CN.4) is set to logic 1 when configured as a slave, and a
274
occur in all SPI0 modes.
the transmit buffer has not been emptied to the SPI shift register. When this occurs, the write to
SPI0DAT will be ignored, and the transmit buffer will not be written.This flag can occur in all SPI0
modes.
multi-master mode and the NSS pin is pulled low. When a Mode Fault occurs, the MSTEN and SPIEN
bits in SPI0CN are set to logic 0 to disable SPI0 and allow another master device to access the bus.
transfer is completed and the receive buffer still holds an unread byte from a previous transfer. The new
byte is not transferred to the receive buffer, allowing the previously received data byte to be read. The
data byte which caused the overrun is lost.
Rev. 1.2
Related parts for C8051F587-IMR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![CP2102EK](/photos/9/3/90395/cp2102ek_tmb.jpg)
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CP2103EK](/photos/9/6/90669/cp2103ek_tmb.jpg)
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CP2201EK](/photos/9/9/90977/cp2201ek_tmb.jpg)
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CAPTOUCHSENSEDC](/photos/9/20/92001/captouchsensedc_tmb.jpg)
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![CAPTOUCHSENSESK](/photos/9/20/92002/captouchsensesk_tmb.jpg)
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F320DK](/photos/9/20/92068/c8051f320dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F120DK](/photos/9/20/92070/c8051f120dk_tmb.jpg)
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F310DK](/photos/9/23/92300/c8051f310dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F226DK](/photos/9/23/92302/c8051f226dk_tmb.jpg)
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F300DK](/photos/9/23/92305/c8051f300dk_tmb.jpg)
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F330DK](/photos/9/23/92306/c8051f330dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F005DK](/photos/9/23/92307/c8051f005dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F020DK](/photos/9/23/92314/c8051f020dk_tmb.jpg)
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F340DK](/photos/9/23/92323/c8051f340dk_tmb.jpg)
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![C8051F410DK](/photos/9/23/92324/c8051f410dk_tmb.jpg)
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: