AT91SAM7SE256-AU Atmel, AT91SAM7SE256-AU Datasheet - Page 353

• Manufacturer Part Number: AT91SAM7SE256-AU
• Description: IC ARM7 MCU FLASH 256K 128-LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7SE256-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: EBI/EMI, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 88
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 128-LQFP
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 88
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7S-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7SE-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 88
• Ram Memory Size: 32KB
• Cpu Speed: 48MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• For Use With: AT91SAM7SE-EK - EVAL BOARD FOR AT91SAM7SEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

32.7
32.7.1
32.7.2
32.7.3
32.7.4
6222F–ATARM–14-Jan-11
Master Mode
Definition
Application Block Diagram
Programming Master Mode
Master Transmitter Mode
The Master is the device which starts a transfer, generates a clock and stops it.
Figure 32-5. Master Mode Typical Application Block Diagram
The following registers have to be programmed before entering Master mode:
After the master initiates a Start condition when writing into the Transmit Holding Register,
TWI_THR, it sends a 7-bit slave address, configured in the Master Mode register (DADR in
TWI_MMR), to notify the slave device. The bit following the slave address indicates the transfer
direction, 0 in this case (MREAD = 0 in TWI_MMR).
The TWI transfers require the slave to acknowledge each received byte. During the acknowl-
edge clock pulse (9th pulse), the master releases the data line (HIGH), enabling the slave to pull
it down in order to generate the acknowledge. The master polls the data line during this clock
pulse and sets the Not Acknowledge bit (NACK) in the status register if the slave does not
acknowledge the byte. As with the other status bits, an interrupt can be generated if enabled in
the interrupt enable register (TWI_IER). If the slave acknowledges the byte, the data written in
the TWI_THR, is then shifted in the internal shifter and transferred. When an acknowledge is
detected, the TXRDY bit is set until a new write in the TWI_THR. When no more data is written
into the TWI_THR, the master generates a stop condition to end the transfer. The end of the
complete transfer is marked by the TWI_TXCOMP bit set to one. See
and
1. DADR (+ IADRSZ + IADR if a 10 bit device is addressed): The device address is used
2. CKDIV + CHDIV + CLDIV: Clock Waveform.
3. SVDIS: Disable the slave mode.
4. MSEN: Enable the master mode.
Rp: Pull up value as given by the I²C Standard
Host with
Interface
Figure
to access slave devices in read or write mode.
TWI
32-8.
TWD
TWCK
Serial EEPROM
Atmel TWI
Slave 1
SAM7SE512/256/32 Preliminary
I²C RTC
Slave 2
Controller
I²C LCD
Slave 3
I²C Temp.
Sensor
Slave 4
Figure
Rp
32-6,
Rp
Figure
VDD
32-7,
353