TMPM362F10FG Toshiba, TMPM362F10FG Datasheet - Page 623

• Manufacturer Part Number: TMPM362F10FG
• Description: 32BIT MICROCONTROLLER
• Manufacturer: Toshiba
• Series: TX03r

Specifications of TMPM362F10FG

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: I²C, Microwire, SIO, SPI, SSP, UART/USART
• Peripherals: DMA, WDT
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Package / Case: 144-LQFP
• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 144
• Package: LQFP(20x20)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 5
• Uart/sio (ch): 12
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: 16
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Number Of I /o: -
• Eeprom Size: -
• Oscillator Type: -
• Lead Free Status / Rohs Status: Details
• Other names: Q5704184A

20.4.3
20.4.2.2
bled. If the value of the conversion result register specified by ADMOD3<ADREGS0> and AD-
MOD5<ADREGS1> becomes larger or smaller ("Larger" or "Smaller" to be designated by ADMOD3<ADO-
BIC0> and ADMOD5<ADBIC1>) than the value of a comparison register, the AD monitor function inter-
rupt (INTADM0,INTADM1) is generated. This comparison operation is performed each time a result is stor-
ed in a corresponding conversion result register.
reading the conversion result, the conversion result is overwritten. The conversion result storage flag
<ADRxRF> and the overrun flag <OVRx> remain being set.
There are two channels of AD monitor function.
If ADMOD3<ADOBSV0> and ADMOD5<ADOBSV1> are set to "1", the AD monitor function is ena-
If the conversion result register assigned to perform the AD monitor function is continuously used without
PEAT,SCAN> setting. When conditions to start operation are met, a conversion is performed just once
for a channel designated by ADMOD2<HPADCH>. When conversion is completed, the top-priority AD
conversion completion interrupt (INTADHP) is generated, and ADMOD2<EOCFHP> showing the comple-
tion of AD conversion is set to "1". <ADBFHP> returns to "0". EOCFHP flag is cleared to "0" upon read.
AD Monitor Function
(3)
(4)
By interrupting ongoing normal AD conversion, top-priority AD conversion can be performed.
The fixed-channel single conversion is automatically selected, irrespective of the ADMOD0<RE-
Top-priority AD conversion activated while top-priority AD conversion is under way is ignored.
Note:Top-priority A/D conversion interrupt cannot generate DMA transfer request.To generate DMA trans-
Top-priority AD conversion
peat conversation mode.
sion is completed, ADMOD0<EOCFN> is set to "1". ADMOD0<ADBFN> is not cleared to "0". It re-
mains at "1". The timing with which the conversion completion interrupt request (INTAD) is gener-
ated can be selected by setting ADMOD0<ITM> to an appropriate setting. <EOCFN> is set with
the same timing as this interrupt INTAD is generated.
peat conversion mode.
AD scan conversion is completed, ADMOD0<EOCFN> is set to "1", and the conversion comple-
tion interrupt request (INTAD) is generated. ADMOD0<ADBFN> is cleared to "0". It remains at
"1". <EOCFN> is cleared to "0" upon read.
fer request, please use A/D conversion completion interrupt (INTAD).
If ADMOD0<REPEAT, SCAN> is set to "10", AD conversion is performed in fixed channel re-
In this mode, AD conversion is performed repeatedly for one channel selected. After AD conver-
By reading <EOCFN>, it is cleared to "0".
If ADMOD0<REPEAT, SCAN> is set to "11", AD conversion is performed in the channel scan re-
In this mode, AD conversion is performed repeatedly for a scan channel selected. Each time one
Fixed channel repeat conversion mode
Channel scan repeat conversion mode
Page 599
TMPM362F10FG