AT32UC3C2512C Atmel Corporation, AT32UC3C2512C Datasheet - Page 973

• Manufacturer Part Number: AT32UC3C2512C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2512C

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

33.6.2.3
Figure 33-6. 2-bit Gray Up/Down Counter
33.6.2.4
32117C–AVR-08/11
PWML1
PWML0
PWMH0
PWMH1
DOWNx
2-bit Gray Up/Down Counter for Stepper Motor
Dead-Time Generator
It is possible to configure a couple of channels to provide a 2-bit gray count waveform on 2 out-
puts. Dead-Time generator and other downstream logic can be configured on these channels.
Up or down count mode can be configured on-the-fly by the SMMR register.
When GCEN0 is written to 1, channels 0 and 1 outputs are driven with gray counter.
The dead-time generator uses the comparator output OCx to provide the two complementary
outputs DTOHx and DTOLx, which allows the PWM to drive external power control switches
safely. When the dead-time generator is enabled by writing a one to the DTE bit in the
Mode Register” on page 1035
times) are inserted between the edges of the two complementary outputs DTOHx and DTOLx.
Note that enabling or disabling the dead-time generator is allowed only if the channel is
disabled.
The dead-time is adjustable by the
outputs of the dead-time generator can be adjusted separately by DTH and DTL. The dead-time
values can be updated synchronously to the PWM period by using the
Update Register” on page 1045
The dead-time is based on a specific counter which uses the same selected clock that feeds the
channel counter of the comparator. Depending on the edge and the configuration of the dead-
time, DTOHx and DTOLx are delayed until the counter has reached the value defined by DTH or
DTL. An inverted configuration bit (DTHI and DTLI bits in the CMRx register) is provided for each
outputs to invert the dead-times outputs. The following figure shows the waveform of the dead-
time generator.
GCEN0 = 1
(CMRx), dead-times (also called dead-bands or non-overlapping
(DTUPDx).
”Channel Dead Time Register” on page 1044
”Channel Dead Time
AT32UC3C
(DTx), both
”Channel
973