ST72F521M9T6 STMicroelectronics, ST72F521M9T6 Datasheet - Page 29

• Manufacturer Part Number: ST72F521M9T6
• Description: IC MCU 8BIT 60K FLASH 80-TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F521M9T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 64
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• Processor Series: ST72F5x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 2048 B
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 3.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: 497-6453 - BOARD EVAL BASED ON ST7LNBX497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8244; ST72F521M9T6

SYSTEM INTEGRITY MANAGEMENT (Cont’d)
6.4.2 Auxiliary Voltage Detector (AVD)
The Voltage Detector function (AVD) is based on
an analog comparison between a V
V
ply or the external EVD pin voltage level (V
The V
than the V
order to avoid parasitic detection (hysteresis).
The output of the AVD comparator is directly read-
able by the application software through a real
time status bit (AVDF) in the SICSR register. This
bit is read only.
Caution: The AVD function is active only if the
LVD is enabled through the option byte.
6.4.2.1 Monitoring the V
This mode is selected by clearing the AVDS bit in
the SICSR register.
The AVD voltage threshold value is relative to the
selected LVD threshold configured by option byte
(see
If the AVD interrupt is enabled, an interrupt is gen-
erated when the voltage crosses the V
V
Figure 16. Using the AVD to Monitor V
IT+(AVD)
IT-(AVD)
AVDF bit
AVD INTERRUPT
REQUEST
IF AVDIE bit = 1
LVD RESET
V
V
V
section 14.1 on page
V
IT+(AVD)
IT-
IT+(LVD)
IT-(LVD)
IT-(AVD)
reference value for falling voltage is lower
threshold (AVDF bit toggles).
reference value and the V
IT+
V
reference value for rising voltage in
DD
0
DD
201).
Main Supply
1
DD
INTERRUPT PROCESS
IT-(AVD)
IT+(AVD)
main sup-
V
Early Warning Interrupt
(Power has dropped, MCU not
not yet in reset)
DD
hyst
(AVDS bit=0)
EVD
RESET VALUE
and
or
).
In the case of a drop in voltage, the AVD interrupt
acts as an early warning, allowing software to shut
down safely before the LVD resets the microcon-
troller. See
The interrupt on the rising edge is used to inform
the application that the V
If the voltage rise time t
CPU cycles (depending on the reset delay select-
ed by option byte), no AVD interrupt will be gener-
ated when V
If t
– If the AVD interrupt is enabled before the
– If the AVD interrupt is enabled after the V
V
rupts will be received: the first when the AVDIE
bit is set, and the second when the threshold is
reached.
threshold is reached then only one AVD interrupt
will occur.
rv
IT+(AVD)
is greater than 256 or 4096 cycles then:
threshold is reached, then 2 AVD inter-
Figure
IT+(AVD)
t
1
16.
rv
VOLTAGE RISE TIME
is reached.
rv
ST72F521, ST72521B
DD
is less than 256 or 4096
warning state is over.
INTERRUPT PROCESS
0
IT+(AVD)
29/215