C8051F040-GQ Silicon Laboratories Inc, C8051F040-GQ Datasheet - Page 122
![IC 8051 MCU 64K FLASH 100TQFP](/photos/12/20/122007/c8051f040-gq_sml.jpg)
C8051F040-GQ
Manufacturer Part Number
C8051F040-GQ
Description
IC 8051 MCU 64K FLASH 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F04xr
Datasheets
1.C8051F040-TB.pdf
(328 pages)
2.C8051F040-TB.pdf
(2 pages)
3.C8051F043-GQ.pdf
(328 pages)
Specifications of C8051F040-GQ
Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
100-TQFP, 100-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 13x12b; D/A 2x10b, 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
4.25 KB
Interface Type
CAN/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
64
Number Of Timers
5
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F040DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 8-bit or 13-ch x 12-bit
On-chip Dac
2-ch x 12-bit
No. Of I/o's
64
Ram Memory Size
4352Byte
Cpu Speed
25MHz
No. Of Timers
5
Rohs Compliant
Yes
Data Rom Size
64 KB
A/d Bit Size
12 bit
A/d Channels Available
13
Height
1 mm
Length
14 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Width
14 mm
Package
100TQFP
Device Core
8051
Family Name
C8051F04x
Maximum Speed
25 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1205 - DEV KIT FOR F040/F041/F042/F043
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1204
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F040-GQ
Manufacturer:
SiliconL
Quantity:
702
Company:
Part Number:
C8051F040-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F040-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F040-GQR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
C8051F040/1/2/3/4/5/6/7
The hysteresis of the Comparator is software-programmable via its Comparator Control register (CPT-
nCN). The user can program both the amount of hysteresis voltage (referred to the input voltage) and the
positive and negative-going symmetry of this hysteresis around the threshold voltage.
The Comparator hysteresis is programmed using Bits3-0 in the Comparator Control Register CPTnCN
(shown in SFR Definition 11.1). The amount of negative hysteresis voltage is determined by the settings of
the CPnHYN bits. As shown in Table 11.1, settings of approximately 20, 10 or 5 mV of negative hysteresis
can be programmed, or negative hysteresis can be disabled. In a similar way, the amount of positive hys-
teresis is determined by the setting the CPnHYP bits.
Comparator interrupts can be generated on either rising-edge and falling-edge output transitions. (For
Interrupt enable and priority control, see
or falling -edge interrupts are enabled using the comparator’s Rising/Falling Edge Interrupt Enable Bits
(CPnRIE and CPnFIE) in their respective Comparator Mode Selection Register (CPTnMD), shown in SFR
Definition 11.2. These bits allow the user to control which edge (or both) will cause a comparator interrupt.
However, the comparator interrupt must also be enabled in the Extended Interrupt Enable Register (EIE1).
The CPnFIF flag is set to logic 1 upon a Comparator falling-edge interrupt, and the CPnRIF flag is set to
logic 1 upon the Comparator rising-edge interrupt. Once set, these bits remain set until cleared by soft-
ware. The output state of a Comparator can be obtained at any time by reading the CPnOUT bit. A Com-
parator is enabled by setting its respective CPnEN bit to logic 1, and is disabled by clearing this bit to logic
0.Upon enabling a comparator, the output of the comparator is not immediately valid. Before using a com-
parator as an interrupt or reset source, software should wait for a minimum of the specified “Power-up
time” as specified in Table 11.1, “Comparator Electrical Characteristics,” on page 126.
122
(Programmed with CPnHYP Bits)
Positive Hysteresis Voltage
INPUTS
OUTPUT
VIN+
VIN-
CIRCUIT CONFIGURATION
Positive Hysteresis
CPn-
CPn+
VIN+
VIN-
Disabled
V
OL
Figure 11.2. Comparator Hysteresis Plot
V
OH
+
_
CPn
Section “12.3. Interrupt Handler” on page
Positive Hysteresis
Maximum
OUT
Rev. 1.5
Negative Hysteresis
Disabled
Negative Hysteresis
(Programmed by CPnHYN Bits)
Maximum
Negative Hysteresis Voltage
153). The rising and/