C8051F040-GQ Silicon Laboratories Inc, C8051F040-GQ Datasheet - Page 210
![IC 8051 MCU 64K FLASH 100TQFP](/photos/12/20/122007/c8051f040-gq_sml.jpg)
C8051F040-GQ
Manufacturer Part Number
C8051F040-GQ
Description
IC 8051 MCU 64K FLASH 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F04xr
Datasheets
1.C8051F040-TB.pdf
(328 pages)
2.C8051F040-TB.pdf
(2 pages)
3.C8051F043-GQ.pdf
(328 pages)
Specifications of C8051F040-GQ
Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
100-TQFP, 100-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 13x12b; D/A 2x10b, 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
4.25 KB
Interface Type
CAN/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
64
Number Of Timers
5
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F040DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 8-bit or 13-ch x 12-bit
On-chip Dac
2-ch x 12-bit
No. Of I/o's
64
Ram Memory Size
4352Byte
Cpu Speed
25MHz
No. Of Timers
5
Rohs Compliant
Yes
Data Rom Size
64 KB
A/d Bit Size
12 bit
A/d Channels Available
13
Height
1 mm
Length
14 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Width
14 mm
Package
100TQFP
Device Core
8051
Family Name
C8051F04x
Maximum Speed
25 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1205 - DEV KIT FOR F040/F041/F042/F043
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1204
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F040-GQ
Manufacturer:
SiliconL
Quantity:
702
Company:
Part Number:
C8051F040-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F040-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F040-GQR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
C8051F040/1/2/3/4/5/6/7
17.1.7. Crossbar Pin Assignment Example
In this example (Figure 17.6), we configure the Crossbar to allocate Port pins for UART0, the SMBus,
UART1, /INT0, and /INT1 (8 pins total). Additionally, we configure the External Memory Interface to oper-
ate in Multiplexed mode and to appear on the Low ports. Further, we configure P1.2, P1.3, and P1.4 for
Analog Input mode so that the voltages at these pins can be measured by ADC2. The configuration steps
are as follows:
210
1. XBR0, XBR1, and XBR2 are set such that UART0EN = 1, SMB0EN = 1, INT0E = 1, INT1E =
2. We configure the External Memory Interface to use Multiplexed mode and to appear on the
3. We configure the desired Port 1 pins to Analog Input mode by setting P1MDIN to 0xE3 (P1.4,
4. We enable the Crossbar by setting XBARE = 1: XBR2 = 0x42.
5. We set the UART0 TX pin (TX0, P0.0) and UART1 TX pin (TX1, P0.4) outputs to Push-Pull by
6. We configure all EMIF-controlled pins to push-pull output mode by setting P0MDOUT |= 0xE0;
7. We explicitly disable the output drivers on the 3 Analog Input pins by setting P1MDOUT =
1, and EMIFLE = 1. Thus: XBR0 = 0x05, XBR1 = 0x14, and XBR2 = 0x02.
Low ports. PRTSEL = 0, EMD2 = 0.
P1.3, and P1.2 are Analog Inputs, so their associated P1MDIN bits are set to logic 0).
-
-
-
-
-
-
-
setting P0MDOUT = 0x11.
P2MDOUT = 0xFF; P3MDOUT = 0xFF.
0x00 (configure outputs to Open-Drain) and P1 = 0xFF (a logic 1 selects the high-impedance
state).
UART0 has the highest priority, so P0.0 is assigned to TX0, and P0.1 is assigned to RX0.
The SMBus is next in priority order, so P0.2 is assigned to SDA, and P0.3 is assigned to
SCL.
UART1 is next in priority order, so P0.4 is assigned to TX1. Because the External Memory
Interface is selected on the lower Ports, EMIFLE = 1, which causes the Crossbar to skip
P0.6 (/RD) and P0.7 (/WR). Because the External Memory Interface is configured in Multi-
plexed mode, the Crossbar will also skip P0.5 (ALE). RX1 is assigned to the next non-
skipped pin, which in this case is P1.0.
/INT0 is next in priority order, so it is assigned to P1.1.
P1MDIN is set to 0xE3, which configures P1.2, P1.3, and P1.4 as Analog Inputs, causing
the Crossbar to skip these pins.
/INT1 is next in priority order, so it is assigned to the next non-skipped pin, which is P1.5.
The External Memory Interface will drive Ports 2 and 3 (denoted by red dots in
Figure 17.6) during the execution of an off-chip MOVX instruction.
Rev. 1.5