ATTINY48-MMU Atmel, ATTINY48-MMU Datasheet - Page 49

• Manufacturer Part Number: ATTINY48-MMU
• Description: MCU AVR 5K FLASH 12MHZ 28-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY48-MMU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 24
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 2-Wire, I2S, SPI
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Package: 28VQFN EP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 12 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• For Use With: ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVR
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.5
8.5.1
8.5.2
8008G–AVR–04/11
Register Description
MCUSR – MCU Status Register
WDTCSR – Watchdog Timer Control Register
The MCU Status Register provides information on which reset source caused an MCU reset.
• Bits 7:4 – Res: Reserved Bits
These bits are reserved and will always read zero.
• Bit 3 – WDRF: Watchdog System Reset Flag
This bit is set if a Watchdog System Reset occurs. The bit is reset by a Power-on Reset, or by
writing a logic zero to the flag.
• Bit 2 – BORF: Brown-out Reset Flag
This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the flag.
To make use of the Reset Flags to identify a reset condition, the user should read and then
Reset the MCUSR as early as possible in the program. If the register is cleared before another
reset occurs, the source of the reset can be found by examining the Reset Flags.
• Bit 7 – WDIF: Watchdog Interrupt Flag
This bit is set when a time-out occurs in the Watchdog Timer and the Watchdog Timer is config-
ured for interrupt. WDIF is cleared by hardware when executing the corresponding interrupt
handling vector. Alternatively, WDIF is cleared by writing a logic one to the flag. When the I-bit in
SREG and WDIE are set, the Watchdog Time-out Interrupt is executed.
• Bit 6 – WDIE: Watchdog Interrupt Enable
When this bit is written to one and the I-bit in the Status Register is set, the Watchdog Interrupt is
enabled. If WDE is cleared in combination with this setting, the Watchdog Timer is in Interrupt
Mode, and the corresponding interrupt is executed if time-out in the Watchdog Timer occurs.
If WDE is set, the Watchdog Timer is in Interrupt and System Reset Mode. The first time-out in
the Watchdog Timer will set WDIF. Executing the corresponding interrupt vector will clear WDIE
and WDIF automatically by hardware (the Watchdog goes to System Reset Mode). This is use-
Bit
0x34 (0x54)
Read/Write
Initial Value
Bit
(0x60)
Read/Write
Initial Value
WDIF
R/W
7
0
R
7
–
0
WDIE
R/W
6
0
R
6
–
0
WDP3
R/W
5
0
R
5
–
0
WDCE
R/W
4
0
R
4
–
0
WDE
WDRF
R/W
R/W
3
X
3
WDP2
R/W
BORF
See Bit Description
R/W
2
0
2
WDP1
R/W
EXTRF
R/W
1
0
1
ATtiny48/88
WDP0
R/W
PORF
0
0
R/W
0
WDTCSR
MCUSR
49