ATMEGA8A-MUR Atmel, ATMEGA8A-MUR Datasheet - Page 154
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
ATMEGA8A-MUR
Manufacturer Part Number
ATMEGA8A-MUR
Description
MCU AVR 8KB FLASH 16MHZ 32QFN
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet
1.ATMEGA8A-MU.pdf
(308 pages)
Specifications of ATMEGA8A-MUR
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
23
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 154 of 308
- Download datasheet (6Mb)
19.8.1
19.9
19.9.1
8159D–AVR–02/11
Accessing UBRRH/UCSRC Registers
Using MPCM
Write Access
the frame type bit (the first stop or the ninth bit) is one, the frame contains an address. When the
frame type bit is zero the frame is a data frame.
The Multi-processor Communication mode enables several Slave MCUs to receive data from a
Master MCU. This is done by first decoding an address frame to find out which MCU has been
addressed. If a particular Slave MCU has been addressed, it will receive the following data
frames as normal, while the other Slave MCUs will ignore the received frames until another
address frame is received.
For an MCU to act as a Master MCU, it can use a 9-bit character frame format (UCSZ = 7). The
ninth bit (TXB8) must be set when an address frame (TXB8 = 1) or cleared when a data frame
(TXB = 0) is being transmitted. The Slave MCUs must in this case be set to use a 9-bit character
frame format.
The following procedure should be used to exchange data in Multi-processor Communication
mode:
Using any of the 5- to 8-bit character frame formats is possible, but impractical since the
Receiver must change between using n and n+1 character frame formats. This makes full-
duplex operation difficult since the Transmitter and Receiver uses the same character size set-
ting. If 5- to 8-bit character frames are used, the Transmitter must be set to use two stop bit
(USBS = 1) since the first stop bit is used for indicating the frame type.
Do not use Read-Modify-Write instructions (SBI and CBI) to set or clear the MPCM bit. The
MPCM bit shares the same I/O location as the TXC Flag and this might accidentally be cleared
when using SBI or CBI instructions.
The UBRRH Register shares the same I/O location as the UCSRC Register. Therefore some
special consideration must be taken when accessing this I/O location.
When doing a write access of this I/O location, the high bit of the value written, the USART Reg-
ister Select (URSEL) bit, controls which one of the two registers that will be written. If URSEL is
zero during a write operation, the UBRRH value will be updated. If URSEL is one, the UCSRC
setting will be updated.
1. All Slave MCUs are in Multi-processor Communication mode (MPCM in UCSRA is set).
2. The Master MCU sends an address frame, and all slaves receive and read this frame.
3. Each Slave MCU reads the UDR Register and determines if it has been selected. If so,
4. The addressed MCU will receive all data frames until a new address frame is received.
5. When the last data frame is received by the addressed MCU, the addressed MCU sets
In the Slave MCUs, the RXC Flag in UCSRA will be set as normal.
it clears the MPCM bit in UCSRA, otherwise it waits for the next address byte and
keeps the MPCM setting.
The other Slave MCUs, which still have the MPCM bit set, will ignore the data frames.
the MPCM bit and waits for a new address frame from Master. The process then
repeats from 2.
ATmega8A
154
Related parts for ATMEGA8A-MUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega8A](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA8A-MU](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 8K FLASH 16MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8A-PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
MCU AVR 8K FLASH 16MHZ 28-PDIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8A-AUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 8KB FLASH 16MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8A-AN](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
8-bit Microcontrollers - MCU AVR 8KB FL 512B EE 1KB SRAM 16 MHZ GRN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8-16AU](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 16MHZ 5V 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8-16MU](/photos/12/32/123219/atmega8-16mu_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 16MHZ 5V 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8-16PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 16MHZ 5V 28DIP
Manufacturer:
Atmel
Datasheet: