ATMEGA8A-MUR Atmel, ATMEGA8A-MUR Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
ATMEGA8A-MUR
Manufacturer Part Number
ATMEGA8A-MUR
Description
MCU AVR 8KB FLASH 16MHZ 32QFN
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet
1.ATMEGA8A-MU.pdf
(308 pages)
Specifications of ATMEGA8A-MUR
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
23
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 20 of 308
- Download datasheet (6Mb)
8159D–AVR–02/11
been written to one by software, hardware clears the bit to zero after four clock cycles. See the
description of the EEWE bit for an EEPROM write procedure.
• Bit 1 – EEWE: EEPROM Write Enable
The EEPROM Write Enable Signal EEWE is the write strobe to the EEPROM. When address
and data are correctly set up, the EEWE bit must be written to one to write the value into the
EEPROM. The EEMWE bit must be written to one before a logical one is written to EEWE, oth-
erwise no EEPROM write takes place. The following procedure should be followed when writing
the EEPROM (the order of steps 3 and 4 is not essential):
The EEPROM can not be programmed during a CPU write to the Flash memory. The software
must check that the Flash programming is completed before initiating a new EEPROM write.
Step 2 is only relevant if the software contains a boot loader allowing the CPU to program the
Flash. If the Flash is never being updated by the CPU, step 2 can be omitted. See
Support – Read-While-Write Self-Programming” on page 212
programming.
Caution: An interrupt between step 5 and step 6 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the EEPROM is
interrupting another EEPROM access, the EEAR or EEDR Register will be modified, causing the
interrupted EEPROM access to fail. It is recommended to have the Global Interrupt Flag cleared
during all the steps to avoid these problems.
When the write access time has elapsed, the EEWE bit is cleared by hardware. The user soft-
ware can poll this bit and wait for a zero before writing the next byte. When EEWE has been set,
the CPU is halted for two cycles before the next instruction is executed.
• Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the correct
address is set up in the EEAR Register, the EERE bit must be written to a logic one to trigger the
EEPROM read. The EEPROM read access takes one instruction, and the requested data is
available immediately. When the EEPROM is read, the CPU is halted for four cycles before the
next instruction is executed.
The user should poll the EEWE bit before starting the read operation. If a write operation is in
progress, it is neither possible to read the EEPROM, nor to change the EEAR Register.
The calibrated Oscillator is used to time the EEPROM accesses.
gramming time for EEPROM access from the CPU.
Figure 7-4.
Note:
Symbol
EEPROM Write (from CPU)
1. Wait until EEWE becomes zero.
2. Wait until SPMEN in SPMCR becomes zero.
3. Write new EEPROM address to EEAR (optional).
4. Write new EEPROM data to EEDR (optional).
5. Write a logical one to the EEMWE bit while writing a zero to EEWE in EECR.
6. Within four clock cycles after setting EEMWE, write a logical one to EEWE.
1. Uses 1MHz clock, independent of CKSEL Fuse settings.
EEPROM Programming Time
Number of Calibrated RC Oscillator
Cycles
8448
(1)
Table 7-4
Typ Programming Time
for details about boot
ATmega8A
lists the typical pro-
8.5ms
“Boot Loader
20
Related parts for ATMEGA8A-MUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega8A](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA8A-MU](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 8K FLASH 16MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8A-PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
MCU AVR 8K FLASH 16MHZ 28-PDIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8A-AUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 8KB FLASH 16MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8A-AN](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
8-bit Microcontrollers - MCU AVR 8KB FL 512B EE 1KB SRAM 16 MHZ GRN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8-16AU](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 16MHZ 5V 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8-16MU](/photos/12/32/123219/atmega8-16mu_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 16MHZ 5V 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8-16PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 16MHZ 5V 28DIP
Manufacturer:
Atmel
Datasheet: