AT91SAM9260B-CU-999 Atmel, AT91SAM9260B-CU-999 Datasheet - Page 404

• Manufacturer Part Number: AT91SAM9260B-CU-999
• Description: IC MCU ARM9 217LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9260B-CU-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: POR, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, EBI, I2S, SPI, USART
• Maximum Clock Frequency: 180 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9260-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• For Use With: AT91SAM9260-EK - KIT EVAL FOR AT91SAM9260AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

30.10.4.2
30.10.4.3
30.10.4.4
30.10.4.5
30.10.5
30.10.5.1
404
AT91SAM9260
Data Transfer
Write Sequence
Clock Synchronization Sequence
General Call
Read Operation
Note that a STOP or a repeated START always follows a NACK.
See
In the case of a Write sequence (SVREAD is low), the RXRDY (Receive Holding Register
Ready) flag is set as soon as a character has been received in the TWI_RHR (TWI Receive
Holding Register). RXRDY is reset when reading the TWI_RHR.
TWI continues receiving data until a STOP condition or a REPEATED_START + an address dif-
ferent from SADR is detected. Note that at the end of the write sequence TXCOMP flag is set
and SVACC reset.
See
In the case where TWI_THR or TWI_RHR is not written/read in time, TWI performs a clock
synchronization.
Clock stretching information is given by the SCLWS (Clock Wait state) bit.
See
In the case where a GENERAL CALL is performed, GACC (General Call ACCess) flag is set.
After GACC is set, it is up to the programmer to interpret the meaning of the GENERAL CALL
and to decode the new address programming sequence.
See
The read mode is defined as a data requirement from the master.
After a START or a REPEATED START condition is detected, the decoding of the address
starts. If the slave address (SADR) is decoded, SVACC is set and SVREAD indicates the direc-
tion of the transfer.
Until a STOP or REPEATED START condition is detected, TWI continues sending data loaded
in the TWI_THR register.
If a STOP condition or a REPEATED START + an address different from SADR is detected,
SVACC is reset.
Figure 30-24 on page 405
Figure 30-24 on page
Figure 30-25 on page
Figure 30-27 on page 407
Figure 30-26 on page
describes the write operation.
405.
405.
406.
and
Figure 30-28 on page
408.
6221I–ATARM–17-Jul-09