HD64F3048F16 Renesas Electronics America, HD64F3048F16 Datasheet - Page 141

• Manufacturer Part Number: HD64F3048F16
• Description: IC H8 MCU FLASH 128K 100QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300Hr

Specifications of HD64F3048F16

• Core Processor: H8/300H
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 100-QFP
• Package: 100PQFP
• Family Name: H8
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 70
• Interface Type: SCI
• On-chip Adc: 8-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

UE = 0
The I and UI bits in the CPU’s CCR and the IPR bits enable three-level masking of IRQ
interrupts and interrupts from the on-chip supporting modules.
Figure 5.5 shows the transitions among the above states.
If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an
interrupt request is sent to the interrupt controller.
When the interrupt controller receives one or more interrupt requests, it selects the highest-
priority request, following the IPR interrupt priority settings, and holds other requests pending.
If two or more interrupts with the same IPR setting are requested simultaneously, the interrupt
controller follows the priority order shown in table 5.3.
The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt request
is accepted. If the I bit is set to 1, only NMI is accepted; other interrupt requests are held
pending.
When an interrupt request is accepted, interrupt exception handling starts after execution of the
current instruction has been completed.
In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is
saved indicates the address of the first instruction that will be executed after the return from the
interrupt service routine.
Next the I bit is set to 1 in CCR, masking all interrupts except NMI.
The vector address of the accepted interrupt is generated, and the interrupt service routine
starts executing from the address indicated by the contents of the vector address.
Interrupt requests with priority level 0 are masked when the I bit is set to 1, and are unmasked
when the I bit is cleared to 0.
Interrupt requests with priority level 1 are masked when the I and UI bits are both set to 1, and
are unmasked when either the I bit or the UI bit is cleared to 0.
For example, if the interrupt enable bits of all interrupt requests are set to 1, IPRA is set to
H'20, and IPRB is set to H'00 (giving IRQ
interrupts), interrupts are masked as follows:
a. If I = 0, all interrupts are unmasked (priority order: NMI > IRQ
b. If I = 1 and UI = 0, only NMI, IRQ
c. If I = 1 and UI = 1, all interrupts are masked except NMI.
2
, and IRQ
2
and IRQ
3
are unmasked.
3
interrupt requests priority over other
Rev. 3.00 Sep 27, 2006 page 113 of 872
Section 5 Interrupt Controller
2
> IRQ
3
>IRQ
REJ09B0325-0300
0
…).
0
to IRQ
5