HD64F3048F16 Renesas Electronics America, HD64F3048F16 Datasheet - Page 580

• Manufacturer Part Number: HD64F3048F16
• Description: IC H8 MCU FLASH 128K 100QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300Hr

Specifications of HD64F3048F16

• Core Processor: H8/300H
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 100-QFP
• Package: 100PQFP
• Family Name: H8
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 70
• Interface Type: SCI
• On-chip Adc: 8-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 15 A/D Converter
15.4.2
Scan mode is useful for monitoring analog inputs in a group of one or more channels. When the
ADST bit is set to 1 by software or external trigger input, A/D conversion starts on the first
channel in the group (AN
selected, after conversion of the first channel ends, conversion of the second channel (AN
starts immediately. A/D conversion continues cyclically on the selected channels until the ADST
bit is cleared to 0. The conversion results are transferred for storage into the A/D data registers
corresponding to the channels.
When the mode or analog input channel selection must be changed during analog conversion, to
prevent incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After
making the necessary changes, set the ADST bit to 1. A/D conversion will start again from the
first channel in the group. The ADST bit can be set at the same time as the mode or channel
selection is changed.
Typical operations when three channels in group 0 (AN
described next. Figure 15.4 shows a timing diagram for this example.
1. Scan mode is selected (SCAN = 1), scan group 0 is selected (CH2 = 0), analog input channels
2. When A/D conversion of the first channel (AN
3. Conversion proceeds in the same way through the third channel (AN
4. When conversion of all selected channels (AN
5. Steps 2 to 4 are repeated as long as the ADST bit remains set to 1. When the ADST bit is
Rev. 3.00 Sep 27, 2006 page 552 of 872
REJ09B0325-0300
AN
ADDRA. Next, conversion of the second channel (AN
and conversion of the first channel (AN
interrupt is requested at this time.
cleared to 0, A/D conversion stops. After that, if the ADST bit is set to 1, A/D conversion
starts again from the first channel (AN
0
to AN
Scan Mode (SCAN = 1)
2
are selected (CH1 = 1, CH0 = 0), and A/D conversion is started (ADST = 1).
0
when CH2 = 0, AN
0
).
0
) starts again. If the ADIE bit is set to 1, an ADI
4
when CH2 = 1). When two or more channels are
0
0
) is completed, the result is transferred into
to AN
0
to AN
2
) is completed, the ADF flag is set to 1
1
) starts automatically.
2
) are selected in scan mode are
2
).
1
or AN
5
)