HD6473308RCP10V Renesas Electronics America, HD6473308RCP10V Datasheet - Page 113

• Manufacturer Part Number: HD6473308RCP10V
• Description: MCU 5V 16K,PB-FREE 80-PLCC
• Manufacturer: Renesas Electronics America
• Series: H8® H8/330r

Specifications of HD6473308RCP10V

• Core Size: 8-Bit
• Program Memory Size: 16KB (16K x 8)
• Oscillator Type: Internal
• Core Processor: H8/300
• Speed: 10MHz
• Number Of I /o: 58
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 80-PLCC
• No. Of I/o's: 58
• Ram Memory Size: 512Byte
• Cpu Speed: 10MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 2
• Digital Ic Case: RoHS Compliant
• Controller Family/series: H8/330
• Peripherals: ADC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply (vcc/vdd): -
• Eeprom Size: -
• Data Converters: -
• Peripherals: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MOS Pull-Ups: Are available for input pins, including pins used for input of timer or interrupt
signals. Software can turn the MOS pull-up on by writing a “1” in P6DR, and turn it off by writing
a “0.”
Pins P6
purpose input or output, or for input of free-running timer clock and input capture signals. When a
pin is used for free-running timer input, its P6DDR bit should be cleared to "0;" otherwise the free-
running timer will receive the value in P6DR. If input pull-up is not desired, the P6DR bit should
also be cleared to "0."
Pin P6
signal (FTOA) of the free-running timer. When used for FTOA output, this pin is unaffected by the
values in P6DDR and P6DR, and its MOS pull-up is automatically turned off.
Pin P6
(FTOB) of the free-running timer, or for IRQ
unaffected by the values in P6DDR and P6DR, and its MOS pull-up is automatically turned off.
When this pin is used for IRQ
in P6DR will not generate interrupts.
Pin P6
for IRQ
generate interrupts.
Reset and Hardware Standby Mode: A reset or entry to the hardware standby mode clears
P6DDR and P6DR to all “0” and makes all pins into input port pins with the MOS pull-ups off.
Software Standby Mode: In the software standby mode, the free-running timer control registers
are initialized but P6DDR and P6DR remain in their previous states. All pins become input or
output port pins depending on the setting of P6DDR. Output pins output the values in P6DR. The
MOS pull-ups of input pins are on or off depending on the values in P6DR.
Figures 5-9 to 5-11 shows schematic diagrams of port 6.
1
6
7
7
0
: This pin can be used for general-purpose input or output, or for the output compare A
: This pin can be used for general-purpose input or output, for the output compare B signal
: This pin can be used for general-purpose input or output, or IRQ
, P6
input, P6
2
, P6
3
7
, P6
DDR should normally be cleared to "0," so that the value in P6DR will not
4
and P6
6
input, P6
5
: As indicated in Table 5-12, these pins can be used for general-
6
DDR should normally be cleared to "0," so that the value
6
input. When used for FTOB output, this pin is
98
7
input. When it is used